Grade, specification and delivery confirmed for your requirement, from Nuroil Trading in Sharjah.
Better oxidation stability
Resists breakdown under heat and oxygen more effectively than Group I.
Low sulphur
Supports emissions-conscious modern engine-oil formulation.
Clear, low-odour appearance
Improves finished-product quality perception.
02 / THE MATERIAL
What is Group II base oil?
IN SHORT
Group II is produced by hydrocracking vacuum-distilled petroleum fractions with hydrogen, heat and a catalyst.
Refining
Hydrocracked
Saturates
90% or more
Sulphur
0.03% or less
Viscosity index
80–120
Appearance
Clear, low odour
03 / READING THE GRADES
Reading the grades.
Neutral (N) grades run from light N70 to heavier N600. Choose by the viscosity the blend needs.
01
Viscosity index
80–120. How viscosity changes with temperature: a higher VI means less change across hot and cold conditions.
02
Saturates
90% or more. Together with sulphur and VI, saturates define the API group.
03
Sulphur
0.03% or less. Measured by ASTM D4294 or D2622 and reported on the Certificate of Analysis.
04
Group II+
Some suppliers use this term for higher-VI Group II stocks, typically VI 110–119. Mention this performance band at enquiry stage.
04 / STRENGTHS & LIMITS
What the group does and does not tell you.
What it tells you
At least 90% saturates and no more than 0.03% sulphur, with VI 80–120
Reliable global availability as a current volume leader
A modern fit for conventional and semi-synthetic engine oils
What it does not tell you
Finished-lubricant performance without a matched additive package
Seal compatibility when reformulating from Group I
The batch values: the Certificate of Analysis governs the supplied product
05 / FULL COMPARISON
Catalogue specifications.
Published catalogue values for each Group II grade; they may vary by refinery and origin. The batch Certificate of Analysis governs the supplied product.
Technical data sheet · Typical values
N 70
NUR-BO2-01Mineral base oil · API Group II
Kinematic viscosity at 100°C
On request
Kinematic viscosity at 40°C
On request
Viscosity index
On request
Flash point
On request
Pour point
On request
Sulphur
On request
Typical use
Lighter industrial and hydraulic fluids
Typical values. The Certificate of Analysis for the offered batch decides.
Match the product to the crop, equipment or process and confirm the specification before you order.
01
Engine oils
A primary stock for conventional and semi-synthetic engine oils, including modern API SN/SP formulations.
02
Hydraulic fluids
Better oxidation stability can extend fluid service life compared with Group I.
03
Gear and transmission oils
Higher-viscosity grades support gear-oil and transmission-fluid formulation.
04
Industrial lubricants
A performance step up from Group I without Group III cost where very high VI is unnecessary.
08 / HOW IT IS MADE
How Group II base oil is made.
The hydroprocessing route. Deeper refining gives lower sulphur and a higher viscosity index.
01
Vacuum feedstock
Lubricant-range fractions are separated from crude under vacuum.
02
Hydrocracking
Hydrogen, pressure and catalyst convert aromatics and sulphur compounds.
03
Catalytic dewaxing
Wax molecules are converted to improve cold-flow properties.
04
Hydrofinishing
Final hydrogen treatment improves colour, odour and stability.
09 / COMPATIBILITY & HANDLING
Protect product integrity.
Clean, dry storage and separate lines keep the oil to its specification.
01
Keep it dry
Use closed, clean tanks and protect the oil from moisture and contamination.
02
Separate grades
Dedicate or thoroughly clean lines, pumps and tanks before grade changes.
03
Control temperature
Avoid direct sunlight and extreme temperature fluctuation during storage.
04
Check older seals
When reformulating from Group I, confirm compatibility with seals designed around higher-sulphur stock.
10 / REFERENCE METHODS
Standards and documents.
Each shipment travels with the documents needed to verify and import it.
Trade and safety codes
For customs declarations, shipping documents and safety data sheets.
HS code2710.19Petroleum oils, other than crude: lubricating base oils
ClassificationAPI Group I · II · IIIAPI Base Oil Interchange Guidelines
TransportNot regulatedNot dangerous goods by road, sea or air
01
Certificate of Analysis
Batch results for viscosity, VI, flash point, pour point, colour and other agreed properties.
02
Shipment documents
Commercial invoice, packing list and Certificate of Origin supplied as applicable. MSDS on request.
03
Inspection support
Independent quantity and quality inspection can be coordinated when required.
04
API Base Oil Interchange Guidelines
Defines Group II classification by saturates, sulphur and viscosity index.
05
ASTM D445 / D2270 / D4294
Reference methods for viscosity, viscosity index and sulphur.
06
REACH (EU)
Chemical registration requirements for relevant imports into the EU.
07
Destination regulations
National chemical and commodity import rules vary by market. This is not exhaustive: confirm destination-specific import documentation at enquiry stage.
11 / PACKING & DELIVERY
Packing formats.
Availability depends on the product, quantity and receiving facilities. Confirm the arrangement for your order.
01 / TRIAL OR LOW VOLUME · STAGED USE
Drums
Typically 200 L steel drums, palletised for easy staged handling and storage. Confirm capacity, filling weight and loading arrangements.
Group II is a hydrocracked mineral base oil with at least 90% saturates, no more than 0.03% sulphur and improved oxidation stability.
02What Group II grades are available?
Common grades include N70, N150, N500 and N600. Availability and exact properties are confirmed against the current batch.
03What is the difference between Group II and Group I?
Group II is hydrocracked, giving it higher saturates, lower sulphur and better oxidation stability than solvent-refined Group I.
04What is Group II+?
Group II+ commonly describes a higher-VI Group II stock, typically VI 110–119, below the Group III threshold. Mention this performance band at enquiry stage.
05Is Group II suitable for API SN/SP engine oils?
Yes. Group II is widely used for conventional and semi-synthetic engine oils formulated to API SN/SP performance categories.
06What documents come with the shipment?
A batch Certificate of Analysis is supplied. MSDS, Certificate of Origin and independent inspection can be arranged when requested.
07Which packing formats are available?
Steel drums, IBCs, flexi tanks and road-tanker or bulk supply are available subject to grade, quantity and destination facilities.
08What Incoterms do you offer?
FOB is commonly quoted from UAE ports. CFR and CIF destination-port offers are available after the grade, quantity, packing and destination are confirmed.