Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Lubricants & base oil

Buying Group II base oil: specification, CoA and sampling checklist

A practical checklist for Group II base oil purchases: the limits to specify, CoA lines to check, sampling and receipt tests, and packing notes.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of Group II base oil with refinery and drums
On this page · 6 sections
  1. 011. Write the specification in numbers
  2. 022. Read the certificate of analysis line by line
  3. 033. Agree sampling and inspection
  4. 044. Check on arrival
  5. 055. Packing and handling notes specific to Group II
  6. 066. Commercial and document checklist

Group II base oil is a refined, consistent product, but cargoes still vary between producers and lots, and long supply chains add risk of contamination. A clear specification, a careful read of the certificate of analysis and a simple receipt routine catch most issues before they reach a blend. This checklist is written for blenders and distributors buying Group II neutrals, and it applies whether the oil arrives in bulk, flexitanks, IBCs or drums. Treat it as a starting point and adapt it to the tests your own laboratory can run.

1. Write the specification in numbers

Grade names such as N150 or N500 are not enough. For each grade, define:

  • Kinematic viscosity at 100 °C and, ideally, 40 °C (ASTM D445), as a range
  • Minimum viscosity index (ASTM D2270)
  • Maximum pour point (ASTM D97 or an automated equivalent)
  • Minimum flash point, open cup (ASTM D92)
  • Maximum colour (ASTM D1500) and appearance, clear and bright
  • Saturates minimum and sulphur maximum, to confirm Group II status
  • Noack volatility and cold-cranking simulator limits for engine oil blending
  • Water content maximum (Karl Fischer) and, if relevant, aniline point

2. Read the certificate of analysis line by line

CoA lineWhat to look for
Product name and batch or tank numberMatches the shipping documents and the grade you ordered
Viscosity at 40 and 100 °CWithin your range; both reported so you can calculate blends
Viscosity indexMeets your minimum, especially if buying Group II+
Flash point and NoackNo sign of light-end contamination
Pour pointConsistent with Group II, typically well below zero
Colour and appearanceGroup II is normally 0.5 or lower; a darker colour needs explanation
Saturates and sulphurAt least 90 per cent and at most 0.03 per cent
Test methods and laboratoryRecognised methods; date close to loading

3. Agree sampling and inspection

  • Decide where quality is determined: at the load port, at discharge, or both.
  • For bulk and flexitank shipments, consider independent inspection at loading, covering tank or container cleanliness and sampling.
  • Keep sealed retained samples from loading, labelled with batch and container numbers.
  • For a new source, test a pre-shipment sample in your own formulation before committing to volume.

4. Check on arrival

  1. Inspect seals and container condition; record numbers against documents.
  2. Draw a representative sample before unloading into your tanks.
  3. Check appearance, colour, viscosity at 40 °C, water content and flash point.
  4. Compare with the load-port CoA; a change beyond test reproducibility is a reason to hold the product.
  5. Do not mix into a tank of a different grade or group until it passes.

5. Packing and handling notes specific to Group II

  • Its water-white colour makes any contamination or residue from a previous cargo easy to see, and difficult to hide in a light-coloured finished product. Insist on clean, dedicated or properly cleaned tanks and flexitanks.
  • Low sulphur and low aromatics mean little natural oxidation protection before additives are added, so avoid long storage at high temperature and limit air exposure.
  • Keep Group II separate from Group I in storage unless a blend is intended and qualified, because mixed oils can change additive solubility.
Specify in numbers, check the CoA against them, and keep a sealed load-port sample. Those three steps settle most base oil quality questions.

6. Commercial and document checklist

Confirm the Incoterm (FOB, CFR or CIF), packing type, quantity tolerance, delivery window and how quality claims are handled. Request the CoA, MSDS, certificate of origin and inspection certificate where needed. Nuroil supplies Group II base oil with a CoA on every delivery, and CoO, MSDS and third-party inspection on request. Share your specification through request a quote, or contact us to discuss grades on the Group II base oil page.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote