Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Lubricants & base oil

Group II+ base oil: what the label means and how to specify it

Group II+ is an industry label for high-VI Group II base oil, not an API category. What it usually means and how to write it into a specification.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of Group II base oil with refinery and drums
On this page · 6 sections
  1. 01Where Group II+ sits
  2. 02Why the label exists
  3. 03Typical properties of a Group II+ light neutral
  4. 04Where Group II+ is used
  5. 05How to specify it
  6. 06Documents to request

Base oil offers and data sheets often describe a grade as "Group II+" or "Group II plus". The term is widely used, but it is not an official category. This guide explains where it sits, why it exists and how to make sure you get the properties you actually need when you buy it.

Where Group II+ sits

The API base stock categories define Group II as base stock with at least 90 per cent saturates, no more than 0.03 per cent sulphur and a viscosity index from 80 up to but not including 120. Group III has the same saturates and sulphur limits with a VI of 120 or higher. Group II+ is an informal subset at the top end of Group II.

Definitions vary. Some patents and producers describe Group II+ as Group II with a VI of 110 or more; trade publications commonly cite a range of about 112 to 119. A few sources put the figure around 115. All agree that it remains Group II under the API system.

CategorySaturatesSulphurViscosity indexStatus
Group IIAt least 90 per centAt most 0.03 per cent80 to below 120API category
Group II+As Group IIAs Group IIUpper part of the Group II range, commonly about 110 to 119Industry label
Group IIIAt least 90 per centAt most 0.03 per cent120 or higherAPI category

Why the label exists

Trade publications explain that the term arose to describe Group II stocks suited to blending modern multigrade engine oils such as SAE 5W and 10W grades. These oils need low volatility and good cold-cranking behaviour, which correlate with higher viscosity index. A Group II+ light neutral can often meet these targets with less Group III in the blend.

Typical properties of a Group II+ light neutral

Published data for a Group II+ grade around N150 viscosity illustrate the profile:

  • Viscosity at 100 °C of roughly 5.2 to 5.6 mm²/s
  • Viscosity index around 110 to 119
  • Pour point of about -18 °C maximum
  • Noack volatility limits in the low to mid teens per cent
  • Cold-cranking simulator viscosity limits stated at -20 or -25 °C
  • Colour of 0.5 or lower

The lighter N70 to N100 grades in a Group II+ slate typically show VI in the same upper band. Heavy grades rarely reach it, so Group II+ is mainly a light and medium neutral label.

Where Group II+ is used

  • SAE 5W-30, 10W-30 and 10W-40 engine oils where volatility and cold-cranking limits are tight
  • Higher-performance hydraulic and turbine oils needing a better viscosity-temperature profile
  • As a partial replacement for Group III in blends, to manage cost while meeting VI targets

How to specify it

Because "Group II+" has no fixed definition, buy against numbers, not the label:

  1. State the minimum viscosity index you need, for example 112 or 115, with the test method (ASTM D2270).
  2. Add the Noack volatility limit and method (ASTM D5800 or CEC L-40).
  3. Add the cold-cranking simulator limit and temperature (ASTM D5293) if you blend engine oils.
  4. Include saturates (ASTM D2007 or equivalent) and sulphur to confirm Group II status.
  5. Keep pour point, flash point, colour and appearance limits as for standard Group II.
Group II+ is a description, not a guarantee. Put the viscosity index, Noack and cold-cranking limits you need in the contract.

Documents to request

Ask for the product data sheet, a certificate of analysis showing the actual VI, Noack and CCS for the lot, and MSDS. For engine oil blenders, ask whether the grade is listed for base oil interchange purposes in the categories you use. Nuroil supplies Group II and Group II+ grades with a CoA on every delivery; request a quote or see the Group II base oil page.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote