Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read5 sections

Knowledge centre · Lubricants & base oil

Group II base oil grades from N70 to N600

A reference to Group II light, medium and heavy neutrals: typical viscosity, VI, pour point, flash point and Noack, and what each grade is used for.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of Group II base oil with refinery and drums
On this page · 9 sections
  1. 01How the grades are named
  2. 02Typical properties by grade
  3. 03What each grade is used for
  4. 04N70 to N100
  5. 05N150
  6. 06N220
  7. 07N500 to N600
  8. 08Comparing Group II grades with Group I equivalents
  9. 09Specifying a Group II grade

Group II base oil is sold as a ladder of neutral grades, usually labelled N70 or 70N at the light end through N150, N220 and N500 or N600 at the heavy end. Producers use their own names and cut points, so grades from two plants with the same label are close but not identical. This guide gives typical properties for each step and the jobs each grade usually does.

How the grades are named

The number is a legacy viscosity label in Saybolt seconds at 100 °F, carried over from Group I practice. N150 corresponds to roughly the same viscosity as SN150, and N500 or N600 to SN500 or SN600. Some producers instead name grades by viscosity at 100 °C or by their own codes. For comparing offers, always use measured kinematic viscosity.

Typical properties by grade

The ranges below are drawn from published Group II product data sheets. They illustrate typical values, not a standard; each producer's data sheet and the lot certificate govern.

GradeViscosity at 100 °C (mm²/s)Viscosity indexPour point max (°C)Flash point min, open cup (°C)
N70 to N100About 3 to 4.7About 100 to 119About -18 or lowerLower than N150; about 200 for the heavier light grades
N150About 5.2 to 5.6About 100 to 119About -15 to -18About 210
N220About 6.3 to 6.6About 100 to 109About -15 to -18About 215
N500 to N600About 10 to 12.5About 95 to 115About -12 to -15About 230 to 255

Across the slate, Group II typically shows ASTM colour of 0.5 or lower, saturates well above the 90 per cent minimum and sulphur far below the 0.03 per cent maximum. Noack volatility limits, where quoted, tend to fall as the grade gets heavier.

Two points are worth noting when reading these figures. First, the light grades vary most between producers, because a small shift in cut point changes viscosity, flash point and volatility together. Second, the viscosity index of heavy Group II grades is often lower than that of the light and middle grades, so a heavy neutral will not always lift the VI of a blend.

What each grade is used for

N70 to N100

Light neutrals for low-viscosity hydraulic and spindle oils, transformer and process oils, metalworking fluids and as a thin component in multigrade engine oils where volatility allows.

N150

The volume grade. It forms the main component of many passenger car and heavy-duty engine oils, ISO VG 32 hydraulic oils and turbine oils. Its low pour point helps cold-weather performance, and its higher VI versions are often sold as Group II+.

N220

A middle grade useful for adjusting engine oil viscosity and for ISO VG 46 to 68 industrial oils without needing as much heavy component.

N500 to N600

Heavy neutrals for heavy-duty diesel engine oils, ISO VG 100 to 220 industrial gear and circulating oils, compressor oils and greases. For still heavier products, blenders combine N500 or N600 with bright stock, often Group I, because Group II heavy grades are limited.

Comparing Group II grades with Group I equivalents

  • Pour point is usually several degrees lower for Group II at the same viscosity, thanks to catalytic dewaxing.
  • Viscosity index is typically equal or higher.
  • Colour is much lighter, and sulphur far lower.
  • Solvency is lower, which can affect additive choice and seal swell.
Pick Group II grades by measured viscosity and VI, not by the label. The same name can cover different cut points from different refineries.

Specifying a Group II grade

For each grade, state the viscosity range at 100 °C or 40 °C, minimum VI, maximum pour point, minimum flash point and any Noack or cold-cranking limits your formulations depend on. Say whether you need saturates and sulphur reported. Nuroil supplies Group II grades with a CoA for every lot and MSDS on request; request a quote or see the Group II base oil page.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote