Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read6 sections

Knowledge centre · Lubricants & base oil

Oxidation stability of Group II base oil and why antioxidant choice matters

Group II base oil lasts longer than Group I once inhibited, but starts with less natural protection. How that shapes turbine, hydraulic and engine oils.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of Group II base oil with refinery and drums
On this page · 6 sections
  1. 01What oxidation does to oil
  2. 02Why Group II responds so well to antioxidants
  3. 03Why uninhibited Group I can look better
  4. 04Choosing antioxidants for Group II
  5. 05What this means in practice
  6. 06Supply and documentation

One of the main reasons blenders choose Group II base oil is longer oil life. Hydraulic, turbine and compressor oils built on Group II often show much longer oxidation test lives than the same additive concept in Group I. Yet an uninhibited Group II oil can actually oxidise faster than an uninhibited Group I. This article explains why both statements are true and what that means for formulation and buying.

What oxidation does to oil

At operating temperature, oxygen reacts with hydrocarbon molecules to form peroxides, acids and eventually polymers. The oil darkens, its viscosity rises, acidity increases and sludge or varnish can form. Antioxidant additives slow this chain reaction by trapping free radicals and decomposing peroxides. Laboratory tests such as the rotating pressure vessel oxidation test (RPVOT, ASTM D2272) and the turbine oil oxidation stability test (TOST, ASTM D943) measure how long an oil resists this process.

Why Group II responds so well to antioxidants

Group II oils are mostly saturated hydrocarbons with very few aromatics, little sulphur and almost no nitrogen. Aromatic and polar molecules are among the first to oxidise and their by-products can speed up further degradation. Remove them, and an antioxidant has much less work to do. Patent literature and industry reports both note that Group II and III base stocks show an improved response to antioxidant additives compared with Group I.

Why uninhibited Group I can look better

Group I keeps much of its natural sulphur, present as thioethers, disulphides and similar compounds. These behave as secondary antioxidants, decomposing peroxides. Industry reports observe that the uninhibited oxidation stability of Group I is often higher than that of Group II for this reason. Once the sulphur is removed by hydroprocessing, that built-in protection is gone, so Group II depends entirely on the additives the blender puts in.

ConditionGroup IGroup II
No antioxidant addedModerate stability from natural sulphur compoundsLower; little natural protection
With a suitable antioxidant packageGoodTypically better and longer-lasting
Solubility of oxidation productsHigherLower; deposits possible if not managed
Colour change in serviceStarts darkerStarts water-white; darkening is more visible

Choosing antioxidants for Group II

  • Primary antioxidants. Aminic and phenolic radical scavengers do most of the work. Combinations of the two often give a synergistic effect.
  • Secondary antioxidants. Because Group II lacks natural sulphur, adding a sulphur- or phosphorus-containing peroxide decomposer can restore that function. Conference papers have shown strong benefits from sulphur-containing antioxidants in low-sulphur base oils.
  • Balance. Too much sulphur chemistry can be counterproductive; some studies note that sulphur species can form acidic products under test conditions.
  • Deposit control. Because oxidation products dissolve less readily in Group II, dispersancy and varnish control need attention, particularly in turbine and hydraulic oils.
Group II starts with less natural protection but rewards the right antioxidant package with longer life than Group I. Formulate for the base oil, not for the grade name.

What this means in practice

Do not compare base oils on uninhibited oxidation alone; compare the finished formulation in the test your customers specify. If you change Group II supplier, rerun the key oxidation test, because process differences between plants can change the response. Store unadditised Group II with limited air exposure and at moderate temperature, as with any base oil.

Supply and documentation

For oxidation-critical products, ask your supplier for viscosity, VI, saturates, sulphur and nitrogen data where available, plus a sample for formulation testing. Keep sourcing consistent once qualified. Nuroil supplies Group II base oil with a CoA on every delivery and samples for qualification on request; see the Group II base oil page or request a quote.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote