Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read6 sections

Knowledge centre · Lubricants & base oil

Additive solubility and seal swell when blending with Group II base oil

Group II base oil is a weaker solvent than Group I. What that means for additive packages, cold haze and elastomer seals, and how blenders adjust.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of Group II base oil with refinery and drums
On this page · 6 sections
  1. 01Why Group II is a weaker solvent
  2. 02Effects on additive packages
  3. 03Effects on seals
  4. 04How formulators compensate
  5. 05A short qualification plan
  6. 06Buying Group II with solvency in mind

Blenders moving a formulation from Group I to Group II base oil often expect only gains: better colour, lower sulphur, improved oxidation life. Most of the time they get them. The surprises, when they come, tend to involve solvency, which affects how well additives stay dissolved and how seals respond. This article explains the mechanism and the checks that prevent problems.

Why Group II is a weaker solvent

Hydroprocessing converts most aromatic and polar molecules into saturated hydrocarbons. Those aromatics and polar species are what give Group I its ability to dissolve polar additives. The more severe the hydrotreatment, the lower the solvency tends to be.

Aniline point is the usual indicator. A higher aniline point means weaker solvent power, and published technical reviews show Group II oils typically running higher than Group I paraffinic oils of the same viscosity. Because the group definitions are broad, Group II oils from different plants can also differ noticeably from each other.

Effects on additive packages

  • Haze or drop-out. Some additives that stay suspended in Group I may come out of solution in Group II, particularly at low temperature or in storage.
  • Different chemistry for the same job. Technical literature notes that an additive type that works well in Group I may need to be replaced by a different chemistry in Group II to perform the same function.
  • Insoluble oxidation products. As oil ages, oxidation by-products are less soluble in highly saturated oil, which can show up as varnish or deposits if dispersancy is not adjusted.
  • Mixed base oils. Combining Group I and Group II can work, but industry articles warn of additive drop-out and seal problems in poorly qualified mixtures.

Effects on seals

Many elastomers swell slightly in contact with mineral oil, and that swell is part of how the seal maintains its fit. Aniline point influences how much an oil swells a given elastomer. A lower-solvency Group II oil typically swells nitrile and similar seals less than a Group I oil, so seals that were sized and aged in Group I service may shrink or harden slightly when switched. In new equipment designed for modern oils this is rarely an issue; in older machinery it deserves a test.

AreaGroup I behaviourGroup II behaviourTypical adjustment
Additive solubilityGoodLower, varies by producerRe-select additives or add a solubiliser
Low-temperature appearanceWax haze in heavy gradesAdditive haze possibleCold storage test of the finished blend
Seal swellModerateLowerSeal compatibility test; seal swell agent if needed
Deposit controlOxidation products stay in solution longerProducts less solubleReview dispersant and antioxidant balance

How formulators compensate

  • Use additive packages that the additive supplier has qualified in Group II.
  • Add a small proportion of a higher-solvency component, such as an ester, alkylated naphthalene or a naphthenic or Group I oil, to lower the aniline point.
  • Use seal swell agents where elastomer tests show shrinkage.
  • Keep the base oil source consistent once a formulation is qualified, because solvency differs between Group II producers.
Group II is not harder to formulate, just different. Test the finished blend for low-temperature clarity and seal compatibility whenever the base oil source changes.

A short qualification plan

  1. Blend the formulation in the new Group II oil at the laboratory scale.
  2. Store samples at low and elevated temperatures for several weeks and inspect for haze and sediment.
  3. Run elastomer immersion tests on the seal materials used by your customers.
  4. Repeat key performance tests named in the product's specification before release.

Buying Group II with solvency in mind

When you request Group II, ask for aniline point alongside the usual viscosity, VI, pour point and Noack figures, and ask for a sample for qualification if you are changing source. Keep a reference sample of the qualified lot. Nuroil can supply Group II base oil with a CoA on every delivery and samples on request; see the Group II base oil page or contact us.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote