Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
NUROIL / BASE OIL / GROUP I

Group I base oil.Solvent refined.

Solvent-refined mineral base oils for established lubricant, grease and industrial formulations, available as SN70, SN150, SN500, SN650 and Bright Stock.

Group I5 grades
ClassificationAPI Group ISolvent refined
Viscosity index80–120ASTM D2270
Grades5SN 70 · SN 150 · SN 500 · SN 650 · Bright Stock
QualityBatch CoAon every shipment
01 / YOUR SUPPLY PARTNER

Why source
base oil from Nuroil.

Grade, specification and delivery confirmed for your requirement, from Nuroil Trading in Sharjah.

  • Pencil sketch of a Group I base oil sample flask beside a drum

    Lowest relative base-stock cost

    Supports cost-sensitive, high-volume formulations.

  • Pencil sketch of the Group I refining route

    Established formulation history

    Familiar handling and performance across mature lubricant markets.

  • Pencil sketch of an IBC, flexitank container and road tanker

    Useful natural solvency

    Helps dissolve and carry some additive systems and process ingredients.

02 / THE MATERIAL

What is
Group I base oil?

IN SHORT

Group I is produced by solvent extraction and dewaxing of vacuum-distilled petroleum fractions.

Pencil sketch of a Group I base oil sample flask beside a drum
Refining
Solvent refined
Saturates
Below 90%
Sulphur
Above 0.03% (typically 0.3–1.0%)
Viscosity index
80–120
Appearance
Amber, less clear
03 / READING THE GRADES

Reading
the grades.

Solvent neutral (SN) grades run from light to heavy viscosity, up to Bright Stock. Choose by the viscosity and film strength the blend needs.

  1. 01

    Viscosity index

    80–120. How viscosity changes with temperature: a higher VI means less change across hot and cold conditions.

  2. 02

    Saturates

    Below 90%. Together with sulphur and VI, saturates define the API group.

  3. 03

    Sulphur

    Above 0.03% (typically 0.3–1.0%). Measured by ASTM D4294 or D2622 and reported on the Certificate of Analysis.

04 / STRENGTHS & LIMITS

What the group
does and does not tell you.

What it tells you

  • Below 90% saturates and above 0.03% sulphur, with VI 80–120
  • A solvent-refined stock with useful natural solvency
  • Access to Bright Stock, a heavy viscosity not every group offers

What it does not tell you

  • Whether a modern low-emission or extended-drain engine oil can use it: confirm the finished formulation target
  • Finished-lubricant performance without a matched additive package
  • The batch values: the Certificate of Analysis governs the supplied product
05 / FULL COMPARISON

Catalogue
specifications.

Published catalogue values for each Group I grade; they may vary by refinery and origin. The batch Certificate of Analysis governs the supplied product.

Technical data sheet · Typical values

SN 70

NUR-BO1-01Mineral base oil · API Group I
Kinematic viscosity at 100°C
On request
Kinematic viscosity at 40°C
On request
Viscosity index
On request
Flash point
On request
Pour point
On request
Sulphur
On request
Density at 15°C
On request
Typical use
Low-viscosity industrial and process oils

Typical values. The Certificate of Analysis for the offered batch decides.

Issued for every batchRequest the Certificate of Analysis
06 / SELECTION

Choosing the Group I grade
for your blend.

Start with the application and the target viscosity. Share both with your enquiry if the formulation target is unclear.

  1. 01
    Requirement

    Low-viscosity industrial and process oils

    SN 70

    Light solvent-neutral stock for low-viscosity industrial and process oils.

  2. 02
    Requirement

    Hydraulic oils, general lubricants and blending

    SN 150

    Light-to-medium stock for hydraulic oils, general lubricants and blending.

  3. 03
    Requirement

    Industrial, automotive and grease formulations

    SN 500

    Higher-viscosity stock for industrial, automotive and grease formulations.

  4. 04
    Requirement

    Blends that need greater viscosity and film strength

    SN 650

    Heavy solvent-neutral stock for blends requiring greater viscosity and film strength.

  5. 05
    Requirement

    Gear oils, greases and heavy-duty lubricants

    Bright Stock

    Very high-viscosity stock for gear oils, greases and heavy-duty lubricants.

Open a product page.

07 / APPLICATIONS

Made for the work
your operation does.

Match the product to the crop, equipment or process and confirm the specification before you order.

Pencil drawing of a hydraulic cylinder and power pack01

Industrial lubricants

A practical base for hydraulic, circulating and general machinery oils. Group I is also used in established general-purpose and older engine-oil formulations where the finished lubricant specification permits it.

Pencil drawing of process oil being pumped into a rubber mixer beside tyres02

Process oils

Cost-effective mineral stock for rubber, textile and other industrial processing.

Pencil drawing of steel parts and a coil protected with rust-preventive oil03

Rust preventives

Useful viscosity and solvency for protective oil and corrosion-control formulations.

Pencil drawing of a grease tin and a mixing vessel04

Gear oils and greases

SN500, SN650 and Bright Stock add body and film strength to heavier blends.

08 / HOW IT IS MADE

From crude fraction
to Group I base oil.

The solvent-refining route. Deeper refining gives lower sulphur and a higher viscosity index.

Crude oilFurnaceVacuumH₂Base oilDrums · bulk01Vacuumdistillation02Solvent extraction03Solvent dewaxing04Finishing andcertification
  1. 01

    Vacuum distillation

    Crude fractions are separated under vacuum to isolate lubricant-range feedstock.

  2. 02

    Solvent extraction

    Furfural or NMP selectively removes aromatic and unstable compounds.

  3. 03

    Solvent dewaxing

    Wax is chilled, crystallised and filtered to improve low-temperature flow.

  4. 04

    Finishing and certification

    The finished stock is stabilised, tested, stored and released against its CoA.

09 / COMPATIBILITY & HANDLING

Protect product
integrity.

Clean, dry storage and separate lines keep the oil to its specification.

  1. 01

    Keep it dry

    Use closed, clean tanks and protect the oil from moisture and contamination.

  2. 02

    Separate grades

    Dedicate or thoroughly clean lines, pumps and tanks before grade changes.

  3. 03

    Control temperature

    For heavy grades and Bright Stock, maintain the agreed transfer temperature without overheating.

  4. 04

    Use safe practice

    Consult the MSDS and use appropriate PPE during transfer, sampling and spill response.

10 / REFERENCE METHODS

Know what
is shipping.

Each shipment travels with the documents needed to verify and import it.

Trade and safety codes

For customs declarations, shipping documents and safety data sheets.

  • HS code2710.19Petroleum oils, other than crude: lubricating base oils
  • ClassificationAPI Group I · II · IIIAPI Base Oil Interchange Guidelines
  • TransportNot regulatedNot dangerous goods by road, sea or air
01
Certificate of Analysis
Batch results for viscosity, VI, flash point, pour point, colour and other agreed properties.
02
Shipment documents
Commercial invoice, packing list and Certificate of Origin supplied as applicable. MSDS on request.
03
Inspection support
Independent quantity and quality inspection can be coordinated when required.
11 / PACKING & DELIVERY

Packing
formats.

Availability depends on the product, quantity and receiving facilities. Confirm the arrangement for your order.

  • 01 / TRIAL OR LOW VOLUME · STAGED USE

    Drums

    Typically 200 L steel drums, palletised for easy staged handling and storage. Confirm capacity, filling weight and loading arrangements.

    Discuss this format
  • ISO tank
    02 / CONTAINERISED · MID-VOLUME SUPPLY

    IBC / flexi tank

    Containerised supply for mid-volume orders. Confirm container compatibility, liner or IBC specification and unloading arrangements at your site.

    Discuss this format
  • 03 / LARGE, REPEAT BULK DELIVERIES

    Road tanker / bulk

    Efficient repeat supply for buyers with dedicated receiving and storage tanks, transfer equipment and a safe unloading bay.

    Discuss this format
13 / PRICE ON THE DAY

Get today’s price.

Prices follow the market, so we quote each order on the day. Share your product, quantity and delivery point and we send a firm offer within 24 hours.

Request today’s price
14 / BUYING THIS RANGE

Frequently asked questions.

Product, documentation, delivery and terms for this range.

Question not listed?

Share your grade, destination and packing and we will answer with the offer.

Discuss your requirement ↗
01What is Group I base oil?
Group I is a mineral base oil produced mainly by solvent refining. It typically has a viscosity index between 80 and 120, less than 90% saturates and more than 0.03% sulphur.
02What Group I grades are available?
Common grades include SN70, SN150, SN500, SN650 and Bright Stock 150. Availability and the exact property range are confirmed against the current batch.
03What is the difference between SN150 and SN500?
SN150 is a lighter-viscosity solvent neutral grade. SN500 is considerably heavier and is selected when a blend needs greater film strength and finished viscosity.
04What is Bright Stock used for?
Bright Stock is a high-viscosity Group I base stock used in gear oils, greases, marine lubricants and other formulations that need body and load-carrying film strength.
05Is Group I suitable for engine oil?
It remains suitable for many established and cost-sensitive lubricant formulations. Modern low-emission or extended-drain engine oils may require Group II or III performance; confirm the finished formulation target.
06What documents come with the shipment?
A batch Certificate of Analysis is supplied. MSDS, Certificate of Origin and independent inspection can be arranged when requested.
07Which packing formats are available?
Steel drums, IBCs, flexi tanks and road-tanker or bulk supply are available subject to grade, quantity and destination facilities.
08What Incoterms do you offer?
FOB is commonly quoted from UAE ports. CFR and CIF destination-port offers are available after the grade, quantity, packing and destination are confirmed.
THE BASE OIL RANGE

Switch group 01 / 03

  1. You’re hereGroup I Base OilSolvent refined, general-purpose
  2. Group II Base OilHydroprocessed, higher purity
  3. Group III Base OilHigh VI, premium formulations
FROM THE KNOWLEDGE CENTRE

Guides & articles

Written by our trade desk to help you specify, compare and buy with confidence.

All guides & articles
ArticleLubricants · 3 minGroup I, II and III base oils in practice

How the three mineral base oil groups differ in refining, stability and solvency, and how blenders choose between them for real…

Read
ArticleLubricants · 4 minHow Group I base oil is made by solvent refining

From vacuum distillation to solvent extraction, dewaxing and finishing: the steps that turn crude oil cuts into Group I SN grades…

Read
ArticleLubricants · 3 minWhy Group I base oil still suits industrial oils and greases

Group I base oil dissolves additives, thickeners and contaminants well. Here is where that solvency is an advantage and where it…

Read
GuideLubricants · 3 minSN150 Group I base oil: specification and test guide

Typical SN150 limits for viscosity, viscosity index, pour point, flash point, colour, Noack and sulphur, with the test behind…

Read
GuideLubricants · 3 minSN500 Group I base oil: specification and test guide

Typical SN500 limits, the tests behind them and what a heavy neutral adds to engine, gear, marine and grease blends.

Read
GuideLubricants · 3 minBlending SN150, SN500 and bright stock to a target viscosity

How Group I grades combine to hit ISO viscosity grades, why simple averaging fails, and how ASTM D7152 is used to estimate blend…

Read
LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote