Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Lubricants & base oil

Why Group I base oil still suits industrial oils and greases

Group I base oil dissolves additives, thickeners and contaminants well. Here is where that solvency is an advantage and where it is not.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of Group I base oil with refinery and drums
On this page · 5 sections
  1. 01Where Group I solvency comes from
  2. 02Applications where solvency helps
  3. 03The trade-offs
  4. 04Mixing Group I with other groups
  5. 05Specifying Group I for these uses

Hydroprocessed base oils dominate modern passenger car engine oils, yet Group I SN grades and bright stock remain in daily use in many blending plants. The main reason is solvency: the ability of the oil to dissolve additives, keep oxidation products in solution and work well with traditional seal materials. This article explains where that property earns Group I its place.

Where Group I solvency comes from

Solvent refining removes much of the aromatic content of a lube distillate but not all of it. Group I base oils typically keep a meaningful share of aromatic and polar molecules, plus naturally occurring sulphur compounds, which keep them below the 90 per cent saturates threshold used for Group II. These molecules make the oil a better solvent for polar materials.

Laboratories often express solvency through the aniline point: the lower the aniline point, the stronger the solvent power. Published technical reviews place paraffinic Group I oils roughly in the 90 to 110 °C range, while Group II and higher groups tend to run higher. Aniline point also rises with viscosity, so comparisons should always be made grade for grade.

Applications where solvency helps

  • Greases. Soap thickeners and many grease additives disperse readily in Group I oils, and heavier grades such as SN500 and bright stock give the base oil viscosity that bearings running slowly under load need.
  • Industrial gear and circulating oils. Extreme-pressure and anti-wear chemistries developed around Group I usually dissolve without extra co-solvents.
  • Marine and large engine oils. High-viscosity blends for slow-speed and medium-speed engines have traditionally used heavy Group I grades and bright stock.
  • Process oils and metalworking fluids. Solvency helps with emulsifier packages and with dissolving residues on metal surfaces.
  • Older equipment. Seals designed around Group I swell behaviour may shrink or harden less predictably if a much lower-solvency oil is substituted without testing.

The trade-offs

The same aromatics that help solvency make Group I more prone to oxidation and sludge once its natural inhibitors are used up, and they limit viscosity index. Group I also has higher sulphur and a darker colour than hydroprocessed oils, which matters for light-coloured products. For modern low-viscosity engine oils with tight volatility limits, Group I is usually not suitable.

There is one subtle advantage on stability: industry reports note that uninhibited Group I oils often resist oxidation better than uninhibited Group II, because residual sulphur compounds behave as secondary antioxidants. Once a modern antioxidant package is added, hydroprocessed oils usually pull ahead.

PropertyGroup I SN gradesPractical effect
SaturatesBelow 90 per centGood solvency, lower oxidation resistance with additives
SulphurAbove 0.03 per cent, often several tenths of a per centNatural antioxidant effect; not suitable where low sulphur is required
Viscosity indexTypically about 90 to 100Adequate for most industrial oils
Viscosity rangeLight neutrals to bright stockHeavy grades available without thickeners

Mixing Group I with other groups

Blenders sometimes combine Group I with Group II or III to balance cost, viscosity and solvency. This can work well, but additive packages qualified in one base oil may not stay fully dissolved in another. Technical reviews warn that mixed oils can show additive drop-out and that seal behaviour changes with aniline point. Any new combination should be checked for appearance at low temperature, filterability and seal compatibility before full production.

Group I is not simply an older, lesser product. Its solvency and heavy-grade availability make it the practical choice for greases, industrial oils and high-viscosity blends.

Specifying Group I for these uses

For grease and industrial oil blending, the useful numbers on an enquiry are viscosity at 40 °C, viscosity index, pour point, flash point, colour and, where it matters to your formulation, sulphur and aniline point. Ask for a recent certificate of analysis and, for a new source, a sample for compatibility tests with your additive package. Nuroil can supply SN150, SN500 and bright stock with a CoA on each delivery; send your requirement through request a quote or read more on the Group I base oil page.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote