Group I base oil is the oldest commercial class of mineral base stock and is still made in refineries around the world. Its character, including its solvency, its natural sulphur content and its slightly darker colour compared with hydroprocessed oils, comes directly from the way it is produced. Knowing the route helps buyers understand why SN150, SN500 and bright stock behave as they do.
Step 1: vacuum distillation and deasphalting
The process starts with atmospheric residue, which is split under vacuum into several lube-range distillates. Each cut becomes the feed for one viscosity grade: a lighter distillate for SN150, a heavier one for SN500, and so on. The sharpness of this separation matters, because overlap between cuts shows up later as a wide boiling range, higher volatility in the light grade or a lower flash point than expected.
The vacuum residue left at the bottom is too heavy to distil. It is treated with liquid propane, which dissolves the oil but rejects asphaltic material. The deasphalted oil is the starting point for bright stock, the heaviest Group I grade.
Step 2: solvent extraction
The distillates and deasphalted oil still contain a large share of aromatic and polar molecules. These hurt viscosity index and oxidation stability, so they are removed by contacting the oil counter-currently with a selective solvent. Furfural has been the most widely used solvent; N-methyl-2-pyrrolidone (NMP) and, in older units, phenol are also used. The solvent dissolves aromatics preferentially, leaving a refined oil called raffinate. The aromatic-rich extract is a by-product, typically used as a process oil or fuel component.
Refiners control the result through the solvent-to-oil ratio, the extraction temperature and the number of stages. More severe extraction gives a higher viscosity index and better stability but a lower yield, which is one reason Group I grades from different refineries are not identical.
Step 3: solvent dewaxing
Raffinate from a paraffinic crude is full of long straight-chain paraffins that crystallise as wax when the oil cools, giving a high pour point. To remove them, the oil is diluted with a solvent pair, commonly methyl ethyl ketone with toluene, chilled well below zero, and filtered. The wax crystals stay on the filter as slack wax; the dewaxed oil and solvent pass through and the solvent is recovered by distillation.
The dewaxing temperature sets the pour point of the finished grade. Heavy grades are harder to dewax completely, which is why SN500 and bright stock tend to have higher pour points than SN150 and are more prone to haze in cold weather.
Step 4: finishing
A final clean-up removes traces of sulphur, nitrogen and oxygen compounds that give colour and instability. Older plants used clay contact; most now use mild hydrofinishing. This step improves colour and colour stability but is far gentler than the hydrocracking used for Group II, so much of the natural sulphur and a meaningful proportion of aromatics remain.
| Stage | What it removes | Main effect on the base oil |
|---|---|---|
| Vacuum distillation | Splits light and heavy cuts | Sets viscosity grade, flash point and volatility |
| Propane deasphalting | Asphaltic material from residue | Makes bright stock feed possible |
| Solvent extraction | Aromatics and polar compounds | Raises viscosity index and stability |
| Solvent dewaxing | Waxy n-paraffins | Lowers pour point and cloud point |
| Hydrofinishing or clay | Colour bodies, some heteroatoms | Improves colour and colour stability |
Why the route defines Group I
Under the API base stock categories, Group I covers oils with less than 90 per cent saturates and/or more than 0.03 per cent sulphur, with a viscosity index from 80 up to 120. Solvent refining cannot reach the saturates and sulphur levels of hydroprocessing, so its products fall naturally into this group. The residual aromatics and sulphur compounds are not only a drawback: they give Group I its good solvency for additives and act as mild natural antioxidants.
Group I is defined less by a single number than by its process: solvent extraction and solvent dewaxing leave enough aromatics and sulphur to keep the oil outside the Group II limits.
What this means when you buy
Because extraction severity, crude source and dewaxing temperature vary between refineries, two cargoes of SN150 can meet the same headline specification but differ in sulphur, colour or pour point. When you enquire, state the grade, the key limits that matter to your blend (viscosity at 40 or 100 °C, viscosity index, pour point, flash point, colour) and ask for a certificate of analysis for the actual lot. Nuroil supplies Group I grades from established producers with a CoA on every delivery and can arrange third-party inspection on request; see the Group I base oil page or request a quote.



