Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read5 sections

Knowledge centre · Lubricants & base oil

SN150 Group I base oil: specification and test guide

Typical SN150 limits for viscosity, viscosity index, pour point, flash point, colour, Noack and sulphur, with the test behind each line.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of Group I base oil with refinery and drums
On this page · 10 sections
  1. 01What the name means
  2. 02Typical specification
  3. 03Parameters that matter most
  4. 04Viscosity at 40 °C
  5. 05Viscosity index
  6. 06Flash point and Noack
  7. 07Pour point
  8. 08Demulsibility and colour
  9. 09Where SN150 is used
  10. 10What to include in an SN150 enquiry

SN150 is the light workhorse of the Group I range. It is used on its own for light hydraulic, spindle and circulating oils, and as the thin component in blends with SN500 or bright stock. This guide sets out what a typical SN150 specification contains, what each parameter tells a blender, and which values deserve a closer look.

What the name means

"SN" stands for solvent neutral: a solvent-refined base oil with a neutral, non-acidic character. The number is a legacy viscosity label based on Saybolt Universal Seconds at 100 °F, so SN150 is roughly 150 SUS at that temperature. In modern units, SN150 sits at about 5 mm²/s at 100 °C and around 30 mm²/s at 40 °C, close to the ISO VG 32 band. The number is a grade label, not a precise measurement, and actual viscosities vary slightly between producers.

Typical specification

The values below are a representative range drawn from published producer data for solvent-refined SN150. Individual refineries set their own limits, so always work from the supplier's sheet and the lot certificate.

ParameterTypical limit or rangeCommon test method
AppearanceClear and brightVisual
Kinematic viscosity at 40 °CAbout 28 to 34 mm²/sASTM D445
Kinematic viscosity at 100 °CAbout 5.0 to 5.5 mm²/sASTM D445
Viscosity index95 minimum is commonASTM D2270
Flash point, open cupAbout 200 to 210 °C minimumASTM D92
Pour pointAbout -6 to -12 °C maximumASTM D97
ColourAbout 1.0 to 1.5 maximumASTM D1500
Noack volatilityOften around 18 to 20 per cent maximum where specifiedASTM D5800 / CEC L-40
SulphurAbove 0.03 per cent by definition; producer data often shows several tenths of a per centASTM D4294 or D2622
Conradson carbon residueVery low, for example 0.03 per cent maximumASTM D189
Total acid numberLow, for example 0.05 mg KOH/g maximumASTM D974

Parameters that matter most

Viscosity at 40 °C

Most SN150 ends up in industrial oils graded by ISO VG at 40 °C, so this is the number blenders calculate from. A lot at the low end of the range may need a little more heavy component to reach VG 32 or VG 46.

Viscosity index

A VI around 95 to 100 is normal for Group I. Lower values mean the oil thins more as it heats; this matters in hydraulic systems that run over a wide temperature range.

Flash point and Noack

These track the light end of the distillation cut. A low flash point or high Noack loss suggests a wider cut, which can raise oil consumption in hot service and affect finished-product flash point limits.

Pour point

For light hydraulic and spindle oils used outdoors in cold climates, the pour point limit of the base oil sets the starting point before any pour point depressant is added.

Demulsibility and colour

Some producers quote water separation time, which is useful for turbine and circulating oils. Colour is mainly a cosmetic and consistency check but a sudden shift between lots can indicate a change in refining.

Where SN150 is used

  • Light hydraulic, spindle and circulating oils near ISO VG 22 to 46
  • Light component in engine oils and industrial gear oils blended with SN500
  • Metalworking and process oils
  • Carrier oil for additive packages and greases with lighter base viscosity
Treat the grade name as a starting point. Buy against measured viscosity at 40 or 100 °C, viscosity index, flash point and pour point, not against "SN150" alone.

What to include in an SN150 enquiry

State the limits you need for viscosity, VI, pour point, flash point and colour, the test methods you accept, and whether you need Noack or sulphur reported. Give the quantity, packing (bulk, flexitank, IBC or drums) and destination. Ask for a recent certificate of analysis and, for a first purchase, a sample. Nuroil supplies SN150 from established producers with a CoA on every delivery and MSDS and third-party inspection on request. Request a quote or see the Group I base oil page.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote