Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Lubricants & base oil

SN500 Group I base oil: specification and test guide

Typical SN500 limits, the tests behind them and what a heavy neutral adds to engine, gear, marine and grease blends.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of Group I base oil with refinery and drums
On this page · 6 sections
  1. 01Where SN500 sits in the range
  2. 02Typical specification
  3. 03How SN500 differs from SN150
  4. 04Typical uses
  5. 05Checks on receipt
  6. 06What to include in an SN500 enquiry

SN500 is the heavy neutral of the Group I range. It gives body to engine oils, industrial gear oils, marine lubricants and greases, and it is the bridge between light neutrals such as SN150 and the much heavier bright stock. Its specification looks similar to SN150 on paper, but several parameters behave differently because of the heavier cut.

Where SN500 sits in the range

Like other solvent neutrals, the number is an old Saybolt viscosity label rather than a modern measurement. In current units, SN500 typically measures around 10.5 to 12 mm²/s at 100 °C and roughly 95 to 110 mm²/s at 40 °C, close to the ISO VG 100 band. Some refineries offer SN600 instead, which sits slightly higher. When comparing offers, check the measured viscosity rather than the grade name.

Typical specification

The ranges below reflect published producer data for solvent-refined SN500. Limits vary by refinery, so the supplier's product data sheet and lot certificate always take precedence.

ParameterTypical limit or rangeCommon test method
AppearanceClear and bright at a stated temperatureVisual
Kinematic viscosity at 40 °CAbout 95 to 110 mm²/sASTM D445
Kinematic viscosity at 100 °CAbout 10.5 to 12 mm²/sASTM D445
Viscosity indexAbout 90 to 95 minimumASTM D2270
Flash point, open cupAbout 220 to 250 °C minimumASTM D92
Pour pointAbout -6 to -9 °C maximumASTM D97
ColourAbout 2.0 to 2.5 maximumASTM D1500
Conradson carbon residueLow, for example 0.08 to 0.1 per cent maximumASTM D189
SulphurAbove 0.03 per cent; often higher than SN150 from the same refineryASTM D4294 or D2622
Total acid numberLow, for example 0.05 mg KOH/g maximumASTM D974

How SN500 differs from SN150

  • Colour. Heavier cuts carry more colour bodies, so a darker ASTM colour is normal and not by itself a sign of poor quality.
  • Carbon residue. Slightly higher than light neutrals. It matters most in engine and compressor oils where deposits are a concern.
  • Pour and cloud point. Heavy cuts are harder to dewax, so pour point limits are usually less severe and haze in cold storage is more common.
  • Flash point. Higher, which helps where the finished product has a minimum flash point requirement.
  • Viscosity index. Often a few points lower than SN150.

Typical uses

  • Heavy component in monograde and multigrade engine oils, blended with SN150
  • Industrial gear oils and circulating oils around ISO VG 100 to 220, with bright stock for the heavier grades
  • Marine system and trunk piston engine oils
  • Base oil for lithium and calcium greases
  • Rubber, ink and process oil applications where a paraffinic heavy oil is needed

Checks on receipt

Because SN500 is often delivered in bulk or flexitanks over long voyages, a short receipt check is worthwhile: appearance (warming a cold sample before judging), viscosity at 40 °C, water content and flash point. Compare these with the load-port certificate. A drop in flash point or a viscosity shift outside test reproducibility can indicate contamination from a previous cargo in the tank or line.

For SN500, judge appearance at a stated temperature, and expect colour and pour point to be a little higher than SN150. Viscosity and flash point are the key acceptance checks.

What to include in an SN500 enquiry

Specify the viscosity window at 40 or 100 °C, minimum VI, flash point, maximum pour point and colour, and say whether you need cloud point, carbon residue or sulphur reported. Include quantity, packing, destination port and the Incoterm you prefer. Ask for a certificate of analysis for the lot and MSDS. Nuroil supplies SN500 with a CoA on every delivery and can arrange independent inspection at loading on request; request a quote or read more on the Group I base oil page.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote