Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read5 sections

Knowledge centre · Lubricants & base oil

Blending SN150, SN500 and bright stock to a target viscosity

How Group I grades combine to hit ISO viscosity grades, why simple averaging fails, and how ASTM D7152 is used to estimate blend ratios.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of Group I base oil with refinery and drums
On this page · 5 sections
  1. 01The building blocks
  2. 02Why simple averaging does not work
  3. 03A practical blending sequence
  4. 04Other properties that change with the ratio
  5. 05Supply implications

Few finished lubricants use a single base oil grade. Industrial oils from ISO VG 32 to VG 460 are usually built by combining SN150, SN500 and bright stock in the right proportions, then adjusting for the additive package. This guide explains how blenders estimate those ratios and what to watch for when a new lot of base oil arrives.

The building blocks

Each Group I grade covers a slice of the viscosity scale. The figures below are approximate and vary between producers, which is exactly why blend ratios need checking against the actual lots.

GradeApproximate viscosity at 40 °CApproximate viscosity at 100 °CNearest ISO VG
SN150About 30 mm²/sAbout 5 mm²/sVG 32
SN500About 95 to 110 mm²/sAbout 11 mm²/sVG 100
Bright stock (150 BS)Several hundred mm²/sAbout 30 mm²/sAbove VG 460

ISO VG grades are defined at 40 °C with a band of plus or minus 10 per cent around the midpoint, so VG 68 covers 61.2 to 74.8 mm²/s and VG 220 covers 198 to 242 mm²/s.

Why simple averaging does not work

Viscosity does not blend linearly. Mixing equal parts of a 30 mm²/s oil and a 100 mm²/s oil does not give 65 mm²/s; the result is noticeably lower, because the thinner component has a disproportionate effect. Blenders therefore use logarithmic relationships, the same family of equations behind the viscosity-temperature charts of ASTM D341.

ASTM D7152 sets out a standard practice for this calculation. It describes two approaches. The Wright method uses each component's viscosity at two temperatures and is generally the more accurate. The simpler ASTM method needs viscosity at one temperature only. Both have inverse forms that solve for the fraction of each component needed to reach a target. The standard notes that for base stock blends, using mass or volume fractions makes little practical difference, and that it does not apply well to viscosity index improvers or additive packages.

A practical blending sequence

  1. Take the measured viscosities from the certificates of analysis of the lots in your tanks, not the grade's nominal values.
  2. Decide which pair of grades brackets the target: SN150 with SN500 for VG 46 to VG 100, SN500 with bright stock for VG 150 to VG 460.
  3. Estimate the ratio with a D7152-type calculation, allowing for the viscosity the additive package will add or, for some packages, take away.
  4. Make a laboratory blend and measure viscosity at 40 °C. Adjust the ratio and record the correction factor for that additive and base oil pairing.
  5. Scale up, and check the first production batch before release.

Other properties that change with the ratio

  • Viscosity index. Blends usually land between the components, but bright stock-rich blends can sit lower than expected.
  • Flash point. The light component dominates. A small proportion of a low-flash SN150 can pull the blend's flash point down.
  • Pour point. Heavy components often set the pour point of the blend, so a VG 220 gear oil may need a pour point depressant even if the SN150 alone would not.
  • Colour and carbon residue. Rise with the bright stock share.
  • Solvency. Remains good across Group I blends, which keeps most industrial additive packages in solution.
Blend from measured lot viscosities, use a logarithmic method such as ASTM D7152, and confirm with a laboratory batch before scaling up.

Supply implications

Because each new lot can shift the ratio slightly, consistent supply of all three grades from the same source simplifies production. When you enquire, give the viscosity windows you work to for each grade rather than grade names alone, and ask for certificates of analysis that report viscosity at both 40 and 100 °C, which lets you use the more accurate two-temperature method. Nuroil can quote SN150, SN500 and bright stock together with a CoA for every lot; request a quote or visit the Group I base oil page.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote