Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
NUROIL / BASE OIL / GROUP III

Group III base oil.VI 120 and above.

Severely hydrocracked and hydro-isomerized base oil with a viscosity index above 120, supplied as 4cSt, 6cSt and 8cSt for synthetic and semi-synthetic lubricants.

Group III3 grades
ClassificationAPI Group IIISeverely hydrocracked and hydro-isomerized
Viscosity index120 or moreASTM D2270
Grades34 cSt · 6 cSt · 8 cSt
QualityBatch CoAon every shipment
01 / YOUR SUPPLY PARTNER

Why source
base oil from Nuroil.

Grade, specification and delivery confirmed for your requirement, from Nuroil Trading in Sharjah.

  • Pencil sketch of a Group III base oil sample flask beside a drum

    Highest petroleum-group oxidation stability

    Supports longer service life and drain intervals.

  • Pencil sketch of the Group III refining route

    High viscosity index

    Maintains more stable viscosity across hot and cold operation.

  • Pencil sketch of an IBC, flexitank container and road tanker

    Lower volatility

    Can reduce oil consumption in high-temperature service.

02 / THE MATERIAL

What is
Group III base oil?

IN SHORT

High pressure and temperature maximise saturates and remove sulphur-bearing compounds. A specialised catalyst then restructures wax into branched iso-paraffins instead of simply removing it.

Pencil sketch of a Group III base oil sample flask beside a drum
Refining
Severely hydrocracked and hydro-isomerized
Saturates
90% or more (typically 99% or more)
Sulphur
0.03% or less (typically below 0.001%)
Viscosity index
120 or more
Appearance
Water-clear
03 / READING THE GRADES

Reading
the grades.

Group III grades are named by approximate kinematic viscosity at 100°C in centistokes, unlike the SN or N naming used for Groups I and II.

  1. 01

    Viscosity index

    120 or more. How viscosity changes with temperature: a higher VI means less change across hot and cold conditions.

  2. 02

    Saturates

    90% or more (typically 99% or more). Together with sulphur and VI, saturates define the API group.

  3. 03

    Sulphur

    0.03% or less (typically below 0.001%). Measured by ASTM D4294 or D2622 and reported on the Certificate of Analysis.

04 / STRENGTHS & LIMITS

What the group
does and does not tell you.

What it tells you

  • At least 90% saturates (typically 99% or more) and VI of 120 or more
  • The base stock behind most full-synthetic commercial lubricants
  • A fit for premium engine and demanding industrial formulations

What it does not tell you

  • Group IV PAO chemistry: if a specification demands it, state that before ordering
  • Food-grade suitability without NSF H1 registration
  • The batch values: the Certificate of Analysis governs the supplied product
05 / FULL COMPARISON

Catalogue
specifications.

Published catalogue values for each Group III grade; they may vary by refinery and origin. The batch Certificate of Analysis governs the supplied product.

Technical data sheet · Typical values

4 cSt

NUR-BO3-01Mineral base oil · API Group III
Kinematic viscosity at 100°C
4.1 – 4.4 cSt
Kinematic viscosity at 40°C
19.0 – 20.0 cSt
Viscosity index
120 min
Flash point
220°C min
Pour point
−12°C max
Sulphur
0.001% wt
Typical use
Lighter synthetic and semi-synthetic engine oils

Typical values. The Certificate of Analysis for the offered batch decides.

Issued for every batchRequest the Certificate of Analysis
06 / SELECTION

Choosing the Group III grade
for your blend.

Start with the application and the target viscosity. Share both with your enquiry if the formulation target is unclear.

  1. 01
    Requirement

    Lighter synthetic and semi-synthetic engine oils

    4 cSt

    Lower-viscosity stock for lighter synthetic and semi-synthetic engine oils.

  2. 02
    Requirement

    Passenger-car synthetic and semi-synthetic oils

    6 cSt

    The common mid-range grade for passenger-car synthetic and semi-synthetic oils.

  3. 03
    Requirement

    Heavy-duty engine oils, industrial lubricants and gear oils

    8 cSt

    Higher-viscosity stock for heavy-duty engine oils, industrial lubricants and gear oils.

Open a product page.

07 / APPLICATIONS

Made for the work
your operation does.

Match the product to the crop, equipment or process and confirm the specification before you order.

Synthetic engine oils pencil illustration01

Synthetic engine oils

The dominant stock behind most full-synthetic and synthetic-blend automotive oils.

High-performance industrial pencil illustration02

High-performance industrial

For turbine, compressor and hydraulic oils in extreme-temperature or extended-service duty.

Extreme-service gear oils pencil illustration03

Extreme-service gear oils

Higher-viscosity grades support demanding gear-oil formulations beyond Group I or II.

Specialty and food grade pencil illustration04

Specialty and food grade

With appropriate processing and NSF H1 certification, suitable for food-processing lubricant bases.

08 / HOW IT IS MADE

How Group III
base oil is made.

The most intensive petroleum route. Hydro-isomerization is the defining additional step and the direct source of Group III's price premium.

Crude oilFurnaceVacuumH₂Base oilDrums · bulk01Vacuum feedstock02Severehydrocracking03Hydro-isomerization04Hydrofinishing
  1. 01

    Vacuum feedstock

    Lubricant-range fractions are separated from crude under vacuum.

  2. 02

    Severe hydrocracking

    Higher pressure and temperature maximise saturates and remove impurities.

  3. 03

    Hydro-isomerization

    A catalyst restructures wax into branched iso-paraffins, lifting VI above 120.

  4. 04

    Hydrofinishing

    Final treatment improves colour, odour, stability and product consistency.

09 / COMPATIBILITY & HANDLING

Protect product
integrity.

Clean, dry storage and separate lines keep the oil to its specification.

  1. 01

    Keep it dry

    Use closed, clean tanks and protect the oil from moisture and contamination.

  2. 02

    Separate grades

    Dedicate or thoroughly clean lines, pumps and tanks before grade changes.

  3. 03

    Control temperature

    Avoid direct sunlight and extreme temperature fluctuation during storage.

  4. 04

    Confirm the full formulation

    Very low sulphur supports broad seal compatibility, but verify the complete additive package when switching from Group I or II.

10 / REFERENCE METHODS

Standards and
documents.

Each shipment travels with the documents needed to verify and import it.

Trade and safety codes

For customs declarations, shipping documents and safety data sheets.

  • HS code2710.19Petroleum oils, other than crude: lubricating base oils
  • ClassificationAPI Group I · II · IIIAPI Base Oil Interchange Guidelines
  • TransportNot regulatedNot dangerous goods by road, sea or air
01
Certificate of Analysis
Batch results for viscosity, VI, flash point, pour point, colour and other agreed properties.
02
Shipment documents
Commercial invoice, packing list and Certificate of Origin supplied as applicable. MSDS on request.
03
Inspection support
Independent quantity and quality inspection can be coordinated when required.
04
API Base Oil Interchange Guidelines
Defines Group III classification by saturates, sulphur and viscosity index.
05
ASTM D445 / D2270 / D4294
Reference methods for viscosity, viscosity index and sulphur.
06
NSF H1 registration
Required when the finished lubricant is intended for incidental food contact.
07
REACH (EU)
Chemical registration requirements for relevant imports into the EU.
08
Destination regulations
National chemical and commodity import rules vary by market. This is not exhaustive: confirm destination-specific import documentation at enquiry stage.
11 / PACKING & DELIVERY

Packing
formats.

Availability depends on the product, quantity and receiving facilities. Confirm the arrangement for your order.

  • 01 / TRIAL OR LOW VOLUME · STAGED USE

    Drums

    Typically 200 L steel drums, palletised for easy staged handling and storage. Confirm capacity, filling weight and loading arrangements.

    Discuss this format
  • ISO tank
    02 / CONTAINERISED · MID-VOLUME SUPPLY

    IBC / flexi tank

    Containerised supply for mid-volume orders. Confirm container compatibility, liner or IBC specification and unloading arrangements at your site.

    Discuss this format
  • 03 / LARGE, REPEAT BULK DELIVERIES

    Road tanker / bulk

    Efficient repeat supply for buyers with dedicated receiving and storage tanks, transfer equipment and a safe unloading bay.

    Discuss this format
13 / PRICE ON THE DAY

Get today’s price.

Prices follow the market, so we quote each order on the day. Share your product, quantity and delivery point and we send a firm offer within 24 hours.

Request today’s price
14 / BUYING THIS RANGE

Frequently asked questions.

Product, documentation, delivery and terms for this range.

Question not listed?

Share your grade, destination and packing and we will answer with the offer.

Discuss your requirement ↗
01Is Group III base oil actually synthetic?
It is petroleum-derived rather than chemically synthesised like Group IV PAO, but it is commonly marketed as synthetic because severe processing produces comparable performance. If a specification explicitly demands Group IV PAO chemistry, state that distinction before ordering.
02What is the difference between Group III and Group IV PAO?
Group III is made from crude oil through severe hydrocracking and hydro-isomerization. Group IV PAO is synthesised from smaller olefin molecules and generally costs more.
03What do 4cSt and 6cSt mean?
They refer to approximate kinematic viscosity at 100°C in centistokes, unlike the SN or N naming commonly used for Groups I and II.
04Why is Group III more expensive?
Its additional severe hydrocracking and catalytic hydro-isomerization are capital- and technology-intensive, producing a viscosity index above 120. It typically carries the highest price of the three petroleum groups.
05Can Group III be used for food-grade lubricants?
Yes, when the selected stock and finished formulation have appropriate further processing and NSF H1 registration. Confirm certification before ordering.
06What documents come with the shipment?
A batch Certificate of Analysis is supplied. MSDS, Certificate of Origin and independent inspection can be arranged when requested.
07Which packing formats are available?
Steel drums, IBCs, flexi tanks and road-tanker or bulk supply are available subject to grade, quantity and destination facilities.
08What Incoterms do you offer?
FOB is commonly quoted from UAE ports. CFR and CIF destination-port offers are available after the grade, quantity, packing and destination are confirmed.
THE BASE OIL RANGE

Switch group 03 / 03

  1. Group I Base OilSolvent refined, general-purpose
  2. Group II Base OilHydroprocessed, higher purity
  3. You’re hereGroup III Base OilHigh VI, premium formulations
FROM THE KNOWLEDGE CENTRE

Guides & articles

Written by our trade desk to help you specify, compare and buy with confidence.

All guides & articles
ArticleLubricants · 3 minWhy Group III base oil is the backbone of modern synthetic engine oils

How severe hydroprocessing gives Group III base oil the very high viscosity index, purity and low volatility that modern engine…

Read
ArticleLubricants · 3 minGroup III base oil or PAO: how blenders choose

Group III base oil and PAO both go into synthetic lubricants. How they differ in origin, cold flow, consistency and cost, and…

Read
ArticleLubricants · 3 minHow Group III base oil helps thin engine oils meet volatility and cold-cranking limits

Thin engine oils must evaporate little yet flow at very low temperatures. Why Group III base oil resolves that conflict, and the…

Read
GuideLubricants · 3 minGroup III base oil 4 cSt, 6 cSt and 8 cSt grades compared

Reference guide to Group III base oil viscosity grades: indicative properties of 4, 6 and 8 cSt stocks and the finished…

Read
GuideLubricants · 3 minGroup III base oil interchange: what the API guidelines mean for blenders

Why one Group III base oil cannot always replace another in an approved engine oil, and how base oil interchange and viscosity…

Read
GuideLubricants · 3 minBuying Group III base oil: a specification and verification checklist

A checklist for buying Group III base oil: test results to require, how to confirm a stock is genuinely Group III, and what to…

Read
LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote