Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read7 sections

Knowledge centre · Lubricants & base oil

Group III base oil or PAO: how blenders choose

Group III base oil and PAO both go into synthetic lubricants. How they differ in origin, cold flow, consistency and cost, and when each makes sense.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of Group III base oil with refinery and drums
On this page · 7 sections
  1. 01Two different routes to a high-performance oil
  2. 02How they compare in service
  3. 03Where Group III is the natural choice
  4. 04Where PAO still earns its place
  5. 05Blending the two
  6. 06Consistency and approvals
  7. 07What to put in an enquiry

Group III base oil and polyalphaolefin (PAO, API Group IV) are the two base stocks most often found in lubricants sold as synthetic. They overlap in many applications, but they are made very differently and they are not interchangeable in every formula. This article sets out how a blender decides between them, or decides to use both.

Two different routes to a high-performance oil

Group III starts from crude oil fractions. Severe hydrocracking and catalytic dewaxing reshape the molecules so that the product is highly saturated, very low in sulphur and has a viscosity index of 120 or more. Its exact composition depends on the feedstock and the refinery's process conditions.

PAO is built up from small, pure molecules. Alpha olefins, typically from ethylene, are joined together (oligomerised) and then hydrogenated. Because the starting material is chemically uniform, the finished fluid has a controlled, predictable molecular structure with no wax and no aromatics.

How they compare in service

PropertyGroup IIIPAO (Group IV)
OriginHydroprocessed petroleum fractionSynthesised from alpha olefins
Viscosity index120 to about 140 for most commercial stocksRoughly 125 to above 200 depending on grade
Low-temperature flowGood, improved further by pour point depressantsExcellent; pour points can reach about -60°C
Oxidation stabilityVery good, close to PAO in many testsVery good
Additive solvencyGoodLower; often needs an ester or other co-base
Batch consistencyDepends on refinery and crudeHighly consistent
Relative costModerateHigher

Where Group III is the natural choice

  • Mainstream synthetic engine oils. Grades such as 5W-30 and many 0W-20 oils can meet their volatility and cold-cranking limits on Group III alone.
  • Additive-heavy formulations. Group III dissolves detergent and dispersant packages better than PAO, so there is less need for a solvent co-base.
  • Cost-sensitive volumes. Driveline fluids, hydraulic oils and heavy-duty diesel oils that need long life without extreme cold performance.

Where PAO still earns its place

  • Very cold climates and arctic hydraulic oils, where the lowest pour point and lowest cold viscosity are needed.
  • High-temperature or long-interval industrial oils, such as some compressor and gear oils, where uniform molecular structure and very high VI reduce thinning and deposits.
  • Formulations with a tight volatility limit at very low viscosity, where a share of PAO closes the last gap.

Blending the two

Many finished oils use both: Group III as the bulk of the base stock and a smaller share of PAO to lift VI, cut volatility or improve the cold-cranking result. This is often the most economical way to meet a demanding specification. Because PAO has limited polarity, formulators usually check additive solubility and seal compatibility when PAO content is high, sometimes adding a small amount of ester.

The question is rarely Group III versus PAO in absolute terms; it is how little PAO, if any, a formulation needs on top of a good Group III stock.

Consistency and approvals

Because Group III properties vary between producers, oils that carry industry or vehicle-maker approvals are tied to tested base oil sources. Changing from one Group III stock to another, or replacing PAO with Group III, may need interchange justification or fresh testing under the relevant guidelines. Blenders should plan approvals before switching sources for cost reasons.

What to put in an enquiry

If you are considering Group III as the main base stock, state the viscosity grades you need, minimum VI, maximum Noack volatility, pour point and cold-cranking requirement, along with the volumes and packing you prefer. Ask for a recent certificate of analysis to compare against your current stock. Nuroil can supply Group III base oil in 4, 6 and 8 cSt grades with a CoA on every shipment; see the Group III page or contact us to discuss a trial lot.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote