Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read6 sections

Knowledge centre · Lubricants & base oil

How Group III base oil helps thin engine oils meet volatility and cold-cranking limits

Thin engine oils must evaporate little yet flow at very low temperatures. Why Group III base oil resolves that conflict, and the tests to watch.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of Group III base oil with refinery and drums
On this page · 6 sections
  1. 01Volatility: what the Noack test measures
  2. 02Cold cranking: what the CCS test measures
  3. 03Why high VI resolves the conflict
  4. 04How the grade choice plays out
  5. 05Other effects of low volatility
  6. 06Practical checks for blenders

Low-viscosity engine oils such as 0W-20 and 0W-16 face a built-in conflict. To crank easily in the cold, the oil must be thin. But thin base oils contain light molecules that boil off in a hot engine, raising oil consumption and leaving heavier, thicker oil behind. Group III base oil is one of the main tools formulators use to satisfy both demands at once.

Volatility: what the Noack test measures

The Noack evaporation test (ASTM D5800 and its equivalents) heats an oil sample to 250°C for one hour under a controlled air flow and reports the percentage of mass lost. Passenger car oil specifications set a maximum Noack loss for the finished oil, commonly around 13% to 15% depending on the specification and grade.

Base oil is the main driver of that result. Additives contribute a little, but the light end of the base stock does most of the evaporating. A light Group I neutral oil at a similar viscosity will typically lose far more than a Group III stock of the same grade.

Cold cranking: what the CCS test measures

The cold-cranking simulator (CCS, ASTM D5293) measures the apparent viscosity of an oil at a low temperature set by the SAE grade, for example -35°C for a 0W oil. If the oil is too thick, the starter motor cannot turn the engine fast enough. A related test, mini-rotary viscometer pumping viscosity, checks that oil can reach the oil pump before the engine is damaged.

Why high VI resolves the conflict

Viscosity index describes how much an oil thins as it warms. A high-VI base oil is relatively thin when cold and relatively thick when hot. That gives the formulator two advantages:

  • Heavier base oil, same cold result. Because a Group III stock has a low cold viscosity for its hot viscosity, a formulator can use a slightly heavier cut, which evaporates less, and still pass the CCS limit.
  • Less viscosity modifier. A higher natural VI means less polymer is needed to reach the multigrade target, which reduces shear loss and deposit-forming material.

A narrow distillation cut adds to the benefit. Group III stocks are usually fractionated tightly, so there is less of the very light material that drives Noack loss.

How the grade choice plays out

A 4 cSt Group III stock is the usual backbone of 0W-20 and 0W-16 oils because it gives good cold cranking. Its Noack loss is the highest of the Group III grades, so formulators often blend in a share of 6 cSt Group III to pull volatility down, or a small proportion of a higher-VI stock to gain margin on both tests. Group III stocks at the upper end of the VI range, often called Group III+, make it easier to meet both limits with less need for PAO.

For a thin engine oil, the most useful base oil numbers are VI, Noack and CCS together; any one of them alone can be misleading.

Other effects of low volatility

  • Stable viscosity over the drain interval. Less evaporation means less thickening as the light ends are lost.
  • Lower oil consumption, which matters for emissions after-treatment systems that can be harmed by oil-derived ash and phosphorus.
  • Reduced deposits in piston ring zones and turbochargers, where evaporating oil can leave residue.

Practical checks for blenders

When qualifying a new Group III source, compare the Noack and CCS values on its certificate of analysis with your current stock, not just the VI and kinematic viscosity. Two oils with the same VI can differ in volatility if their distillation cuts differ. Run a laboratory blend of your formulation and test the finished oil before committing to a full tank.

When you request Group III 4 cSt or 6 cSt from Nuroil, include your Noack and CCS limits alongside viscosity and VI so the offered grade can be matched to the CoA. Details of available grades are on the Group III base oil page.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote