Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read7 sections

Knowledge centre · Lubricants & base oil

Group III base oil 4 cSt, 6 cSt and 8 cSt grades compared

Reference guide to Group III base oil viscosity grades: indicative properties of 4, 6 and 8 cSt stocks and the finished lubricants each one suits.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of Group III base oil with refinery and drums
On this page · 7 sections
  1. 01Why grades are named by viscosity at 100°C
  2. 02Indicative properties by grade
  3. 034 cSt: the cold-cranking grade
  4. 046 cSt: the all-rounder
  5. 058 cSt: the heavier component
  6. 06Combining grades
  7. 07What to state in your enquiry

Group III base oils are sold by their kinematic viscosity at 100°C, usually in three main grades: 4 cSt, 6 cSt and 8 cSt. Some producers also make a 3 cSt grade or heavier stocks, but these three cover most blending needs. This guide explains how the grades differ and which finished lubricants each one is normally used for.

Why grades are named by viscosity at 100°C

The number in the grade name is the approximate kinematic viscosity at 100°C in centistokes (mm²/s), measured by ASTM D445. Unlike Group I, which is still often sold by SUS-based names such as SN150 or SN500, Group III is almost always described by its 100°C viscosity. A "4 cSt" stock may measure anywhere from about 3.9 to 4.4 cSt depending on the producer, so always read the actual value on the certificate of analysis.

Indicative properties by grade

The table shows typical ranges seen on Group III product data. Values vary between refineries and between standard Group III and Group III+ stocks, so treat them as a guide for comparison, not as a specification.

Property (method)4 cSt6 cSt8 cSt
Viscosity at 100°C, cSt (D445)about 3.9–4.4about 5.6–6.5about 7.5–8.3
Viscosity index (D2270)120–135125–140125–140
Noack volatility, % mass (D5800)roughly 12–15roughly 6–9roughly 4–6
Pour point, °C (D97)about -15 to -24about -12 to -21about -12 to -18
Saturates, % mass≥ 90 (often above 99)
Sulphur, % mass≤ 0.03 (often a few mg/kg)
AppearanceClear and bright, water-white

4 cSt: the cold-cranking grade

The lightest of the main grades gives the best low-temperature viscosity and is the backbone of 0W-16, 0W-20 and 5W-20 engine oils. It also suits automatic transmission fluids and low-viscosity hydraulic oils. Its weakness is volatility, so it is often blended with heavier Group III or a share of a higher-VI stock to meet Noack limits.

6 cSt: the all-rounder

The 6 cSt grade is frequently the main component of 5W-30 and 5W-40 passenger car oils and of many 10W-30 and 10W-40 heavy-duty oils. It has much lower volatility than 4 cSt while still giving reasonable cold-cranking results. Blended with 4 cSt, it lets a formulator dial in almost any light multigrade.

8 cSt: the heavier component

The 8 cSt grade is used to lift viscosity in heavier multigrades such as 10W-40, 15W-40 and 5W-50, in gear and driveline oils, and in industrial oils that need higher viscosity with good oxidation stability. Its low volatility also suits oils that run hot. Because Group III is not made in very heavy grades, blenders who need ISO VG 220 and above usually combine it with heavier Group I stocks such as bright stock, or with other heavy bases.

Choose the grade for the finished oil's viscosity, then check that VI, Noack and pour point on the certificate fit the specification you must meet.

Combining grades

Because all three grades are made by the same process, they blend smoothly with each other. A typical approach is to calculate the ratio of two adjacent grades needed to reach a target viscosity, then confirm Noack and cold-cranking results on a laboratory blend. Small changes in the ratio can move volatility by a point or more, so test rather than assume.

What to state in your enquiry

  • Grade or grades required and target viscosity range at 100°C.
  • Minimum VI, maximum Noack and maximum pour point.
  • Monthly or per-shipment volume, packing (drums, flexitank, ISO tank or bulk) and delivery terms.
  • Whether you need certificate of origin, MSDS or third-party inspection alongside the CoA.

Nuroil offers Group III base oil in all three grades. Send your requirements through request a quote, or compare with other base oils on the base oil page.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote