Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Lubricants & base oil

Group III base oil interchange: what the API guidelines mean for blenders

Why one Group III base oil cannot always replace another in an approved engine oil, and how base oil interchange and viscosity read-across work.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of Group III base oil with refinery and drums
On this page · 6 sections
  1. 01The framework in brief
  2. 02Key terms
  3. 03Why Group III interchange is harder
  4. 04What the rules mean in practice
  5. 05How to prepare for a supplier change
  6. 06Information to ask from a supplier

Two Group III base oils can share the same viscosity grade and viscosity index and still behave differently in an engine test. That is why licensed engine oils are tied to tested base oil sources, and why switching supplier is not just a purchasing decision. This guide explains the base oil interchange and viscosity grade read-across framework that blenders work within.

The framework in brief

API 1509, the engine oil licensing and certification system, includes Annex E: guidelines for base oil interchange and viscosity grade read-across. It defines the base oil groups by saturates, sulphur and viscosity index, names the analytical methods used to classify them, and sets out when a formulator may substitute one base stock for another without repeating the full set of engine tests.

The classification methods listed are ASTM D2007 or D7419 for saturates, D2270 for viscosity index, and D1552 or D2622 (among others) for sulphur. For Group III the thresholds are at least 90% saturates, no more than 0.03% sulphur and VI of at least 120.

Key terms

  • Base oil interchange (BOI). Replacing the base stock in an already-tested formulation with a different base stock, keeping the additive package and viscosity modifier unchanged.
  • Viscosity grade read-across (VGRA). Applying test results from one SAE viscosity grade of a formulation to another grade made with the same additive package and base stocks.
  • Slate. A family of base stocks of different viscosities from the same manufacturer and process, in the same group, that are technically substitutable for each other.

Why Group III interchange is harder

The Group III category is broad. Commercial stocks range in VI from 120 to well above 140, and they are made from different feedstocks by different process routes. The simple bulk tests used to classify base oils do not fully predict how a stock will perform in oxidation, deposit or wear engine tests. Industry commentary has long noted that the saturates test, in particular, is imprecise for very highly saturated oils, so two stocks that look the same on paper may not respond identically to the same additives.

For this reason the guidelines generally allow less freedom to swap Group III stocks than to swap within some other groups, and the specific allowances depend on the engine test in question. Additive companies often hold their own data supporting particular Group III sources in their packages.

What the rules mean in practice

SituationTypical consequence
Same Group III slate, different viscosity gradeOften covered by slate or read-across provisions, subject to the guidelines
Different Group III producer, licensed engine oilCheck interchange coverage; may need engine tests or additive supplier data
Small proportion of a different base stockSome minor-component allowances exist; confirm the current limits
Unlicensed industrial or hydraulic oilAPI Annex E does not apply; verify by bench testing and customer specification

The precise percentages and test-by-test allowances change between revisions of Annex E, so blenders should work from the current edition and from their additive supplier's guidance rather than from memory.

For a licensed engine oil, the base oil's name and origin are part of the approval; for an industrial oil, the certificate of analysis and bench tests carry more weight.

How to prepare for a supplier change

  1. List every finished product that uses the current Group III stock and note which carry API, ACEA or vehicle-maker approvals.
  2. Ask your additive supplier whether the proposed Group III source is already covered in their interchange data.
  3. Obtain a full certificate of analysis and, where possible, a typical-properties sheet from the new source.
  4. Run laboratory blends and bench tests (viscosity, CCS, Noack, oxidation) before plant trials.
  5. Keep records of base oil source and batch for each production run, as licensing audits may ask for them.

Information to ask from a supplier

When requesting Group III base oil for an approved product, ask for the producing refinery and slate name, a recent CoA showing saturates, sulphur and VI by the Annex E methods, and confirmation that the source will remain consistent across shipments. Nuroil sources Group III base oil from established producers and provides a CoA with every delivery; certificate of origin and third-party inspection are available on request. Discuss your approval needs through the contact page or the Group III base oil page.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote