Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article4 min read6 sections

Knowledge centre · Water & pool treatment

Sodium bisulphate or hydrochloric acid: choosing a pool pH reducer

Dry sodium bisulphate and liquid hydrochloric acid both lower pool pH. How they differ in handling, residues, dosing and storage, and when each suits.

Written by the Nuroil trade desk, Sharjah

On this page · 6 sections
  1. 01What each product is
  2. 02Handling and storage
  3. 03What stays in the water
  4. 04Comparison at a glance
  5. 05Which suits which site
  6. 06Specifying sodium bisulphate

Every chlorinated pool drifts upwards in pH over time. Fresh plaster, salt chlorinators, aeration from water features and alkaline chlorine products all push it higher, and operators need an acid to pull it back. In practice the choice usually comes down to two products: dry sodium bisulphate, often sold as "dry acid", and liquid hydrochloric acid, also called muriatic acid. Both work. The better choice depends on the site, the staff and the water.

What each product is

Sodium bisulphate (NaHSO₄) is an acid salt: sulphuric acid that has been half neutralised with sodium. It is supplied as a white granular or bead-form solid that dissolves quickly in water and gives a strongly acidic solution. Commercially it is often made by reacting sulphuric acid with sodium chloride, with hydrochloric acid recovered as a co-product.

Hydrochloric acid is a solution of hydrogen chloride gas in water, delivered as a liquid in drums, carboys or bulk. It is a strong acid that fumes when the container is opened.

Both lower pH and total alkalinity by supplying hydrogen ions to the water. The difference lies in what else they bring with them and how they behave before they reach the pool.

Handling and storage

The main reason many operators choose sodium bisulphate is that it is a dry solid. It cannot splash in the way a liquid can, it does not give off acid fumes, and it can be stored in bags or pails without the vapour that corrodes nearby metalwork in a plant room. Spills can be swept up rather than neutralised and hosed away.

That does not make it harmless. Sodium bisulphate is classified as causing serious eye damage, and its dust irritates the eyes, skin and airways. It is also hygroscopic: it picks up moisture from humid air, which can make it cake and leave acidic residues on surfaces. Hydrochloric acid, for its part, needs vented, bunded storage away from chlorine products and metal fittings, plus face and hand protection whenever it is poured.

What stays in the water

Every acid leaves its partner ion behind once the hydrogen has done its work.

  • Sodium bisulphate leaves sodium and sulphate. Sulphate does not evaporate or get consumed; it accumulates with every dose and is only removed when water is replaced.
  • Hydrochloric acid leaves chloride. Chloride also accumulates, but most chlorinated pools, especially salt-chlorinated ones, already carry a large chloride load, so the relative increase is usually small.

Rising sulphate is the most cited drawback of dry acid. At high levels sulphate can attack cement-based surfaces and grout, so pools with plaster, render or tiled concrete finishes, high acid demand and little fresh-water make-up need to watch it. Some salt chlorinator manufacturers discourage dry acid for this reason, particularly in hot, dry climates where evaporation concentrates the water.

Comparison at a glance

FactorSodium bisulphate (dry acid)Hydrochloric acid (liquid)
Physical formGranular solidFuming liquid
Main handling hazardCorrosive dust, eye damageSplashes and acid vapour
Residue left in waterSodium and sulphateChloride
Storage needsDry, sealed, away from chlorine productsVented, bunded, away from chlorine products and metals
Dosing methodPre-dissolve or broadcast by handDilute and pour, or meter by pump
Weight shipped per unit of acidityHigherLower, but includes water

Which suits which site

Sodium bisulphate tends to suit smaller pools, hotels, villas and residential complexes where staff dose by hand, where storage space is limited or shared, and where avoiding liquid acid in a small plant room is a priority. It also suits spas and hot tubs where only small corrections are needed.

Hydrochloric acid, or sulphuric acid on some sites, is generally preferred for large public and competition pools with automatic dosing pumps, high acid demand and trained plant staff. Metering a liquid is simpler than dissolving a solid, and chloride build-up is less of a concern than sulphate at high consumption rates.

Neither acid is "safer" in every respect. Dry acid removes splash and fume risks; liquid acid avoids sulphate build-up. Choose for the site, not the label.

Whichever product is used, never mix it with chlorine products, in storage or in a bucket. Acids react with hypochlorite and chlorinated isocyanurates to release chlorine gas. Add acid to water, dose separately from chlorine, and follow the product SDS.

Specifying sodium bisulphate

When buying dry acid for pool use, state the assay (sodium bisulphate content), the maximum water-insoluble matter, the particle form and size, and whether certification for drinking-water contact is needed. Ask for the SDS and a certificate of analysis for each lot. Nuroil supplies sodium bisulphate on request in bags or bulk bags; a quote request with quantity, packing and destination port is enough to start.

KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote