Adding dry acid to a pool looks simple, but poor technique wastes product, overshoots the target and can damage surfaces near the point of addition. This guide sets out a sound routine for using sodium bisulphate to lower pH and total alkalinity in pools and spas. It does not give fixed dose rates, because the right dose depends on the water volume, the current readings and the product strength. Use the dosing chart on the supplier's label or technical sheet, and always start with less than you think you need.
How dry acid changes the water
Sodium bisulphate releases hydrogen ions as it dissolves. These react first with bicarbonate, which is the main component of total alkalinity, turning it into carbonic acid and carbon dioxide. That lowers both total alkalinity and pH. Total alkalinity acts as a buffer: the higher it is, the more acid is needed to move pH, and the faster pH climbs back afterwards as carbon dioxide escapes at the surface.
This is why operators who only ever "correct pH" often find themselves adding acid every day. The lasting fix is usually to bring alkalinity to the right level first.
Target ranges
Public health guidance commonly sets pool pH between 7.2 and 7.8, with many operators aiming for 7.4 to 7.6, where chlorine works well and swimmers are comfortable. Local pool codes take priority and may be stricter. Total alkalinity targets depend on the surface and the chlorine product; consult the code or the surface manufacturer's guidance.
Step-by-step routine
- Test before you dose. Measure pH, total alkalinity, free chlorine, calcium hardness and, if used, cyanuric acid. Record the water volume accurately; dose calculations are only as good as this figure.
- Decide what you are correcting. If total alkalinity is in range and only pH is high, a small dose is enough. If total alkalinity is high, plan a staged reduction over several days.
- Calculate a partial dose. Using the supplier's chart, work out the dose for the full correction and add half to two-thirds of it. Overshooting pH is harder to fix than undershooting.
- Pre-dissolve where practical. Add the granules to a clean plastic bucket of pool water, never water onto the granules, and stir with a plastic or wooden paddle until dissolved. Use a bucket kept only for acid.
- Add with circulation running. Pour the solution slowly into the deep end or in front of a return inlet, away from swimmers, skimmers and metal fittings. Do not let undissolved granules sit on plaster or vinyl.
- Circulate and retest. Allow several hours of circulation, then test again before adding more.
- Keep chlorine separate. Do not add chlorine products at the same time or through the same bucket. Allow time between additions.
Lowering alkalinity without crashing pH
Bringing down high alkalinity takes repeated acid additions. A common approach is to lower pH towards the bottom of the acceptable range with acid, then aerate the water with fountains, jets or a lowered water level over spillways. Aeration drives off carbon dioxide, which raises pH again without restoring alkalinity. Repeating the cycle reduces alkalinity step by step. Bathing should not resume until pH is back in range.
Common mistakes
| Mistake | Result | Better practice |
|---|---|---|
| Full calculated dose in one go | pH overshoots, corrosive water | Add in stages and retest |
| Broadcasting granules onto still water | Etching or bleaching of the surface | Pre-dissolve, dose with pump running |
| Using the chlorine bucket | Chlorine gas release | Dedicated acid bucket, labelled |
| Dosing into the skimmer | Concentrated acid through pump and heater | Dose into the pool body |
| Correcting pH while alkalinity is high | Daily acid, sulphate build-up | Fix alkalinity first |
Test, add part of the dose, circulate, retest. Patience costs less acid than correction.
Personal protection
Sodium bisulphate dust causes serious eye damage and irritates skin and airways. Wear chemical splash goggles and acid-resistant gloves, pour low to avoid dust, and work upwind outdoors. Keep the product in its closed container and follow the first-aid instructions on the SDS.
Ordering for regular dosing
For routine use, choose a granular product with consistent assay so that your dosing chart stays valid from lot to lot, and ask for a certificate of analysis with each delivery. Pack size should match how quickly an opened bag is used, since the product absorbs moisture once opened. For supply questions, contact Nuroil through the contact page.
