Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read7 sections

Knowledge centre · Urea & fertilizers

Urea specifications explained

A reference to the parameters on a urea certificate of analysis: nitrogen, biuret, moisture, size, conditioner, free ammonia and crushing strength.

Written by the Nuroil trade desk, Sharjah

Illustration of urea granules and bagged fertilizer
On this page · 7 sections
  1. 01Nitrogen content
  2. 02Biuret
  3. 03Moisture
  4. 04Particle size
  5. 05Conditioner, free ammonia and strength
  6. 06Reading a certificate of analysis
  7. 07Writing your specification

A urea specification or certificate of analysis (CoA) usually lists between four and ten parameters. Each one tells you something different about how the product will perform in the field, in a blender or in an industrial process. This guide explains the common parameters, typical values seen on producer specifications, and why they matter. Always check the actual contract specification and the national standard that applies in your market.

Nitrogen content

Pure urea contains about 46.6% nitrogen. Commercial fertilizer urea is normally specified at 46.0% minimum on a mass basis, the highest nitrogen content of any common solid fertilizer. Small shortfalls usually point to moisture, conditioner or impurities. Coated feed grades may be slightly lower by design.

Biuret

Biuret forms when two urea molecules combine and release ammonia, mainly when urea melt is held at high temperature during finishing. It can harm sensitive crops, especially when urea is applied as a foliar spray or placed close to seed. Typical fertilizer specifications set a maximum of 1.0%, though some markets allow up to 1.2% or 1.5%. Foliar and technical uses need lower levels; diesel exhaust fluid under ISO 22241 allows no more than 0.3% in the finished solution.

Moisture

Urea is hygroscopic. Typical specifications set moisture at 0.5% maximum. Higher moisture increases the risk of caking, softens particles and can reduce nitrogen content slightly. Moisture is measured at loading, so storage and transport conditions afterwards still matter.

Particle size

Size is expressed as the percentage of product falling within a size band. Producer specifications commonly quote prilled urea at 90% minimum between 1 and 3.5 mm, and granular urea at 95% minimum between 2 and 4.5 mm. Some buyers also specify a size guide number or limits on fines. Size affects spreading width, blending compatibility, dust and dissolving speed.

Conditioner, free ammonia and strength

01

Formaldehyde or urea-formaldehyde conditioner

is added by many producers to improve hardness and resist caking. Typical levels are a few tenths of a percent. Technical users making diesel exhaust fluid usually need conditioner-free urea.
02

Free ammonia

is residual ammonia from the process. Producers report it in parts per million; limits differ between specifications. High levels can give an odour and may affect particle strength.
03

Crushing strength

is the force a single particle withstands before breaking, measured in newtons or kilograms. Granular urea is considerably stronger than prilled urea. Strength matters for bulk shipping and repeated handling.
ParameterTypical fertilizer specificationWhy it matters
Total nitrogen46.0% minNutrient value and pricing basis
Biuret1.0% max (market dependent)Crop safety, especially foliar use
Moisture0.5% maxCaking and handling
Size, prilled90% min within 1 to 3.5 mmSpreading, dissolving
Size, granular95% min within 2 to 4.5 mmSpreading, blending, dust
Formaldehyde conditionerTypically a few tenths of a percent, if usedAnti-caking, hardness
Free ammoniaStated in ppm; limits varyOdour, quality indicator
Crushing strengthStated by producerBreakage and dust in handling

Reading a certificate of analysis

  • Check that each result is within the contract limit, not just the producer's typical value.
  • Confirm the test methods used, as results can differ between methods.
  • Match the lot or batch number on the CoA to the shipment documents.
  • For critical uses, compare the producer's CoA with an independent inspection report taken at loading.
A good urea specification names the limits that matter for your use, the test methods and who samples the cargo.

Writing your specification

For an enquiry, list the grade (agricultural, feed or technical), form, and your limits for nitrogen, biuret, moisture and size, plus conditioner requirements. Add packing, quantity and destination. Nuroil provides a CoA with every delivery, and a certificate of origin, SDS or third-party inspection on request.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote