Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read5 sections

Knowledge centre · Urea & fertilizers

Bulk blending fertilizers and which products should not be mixed

Compatibility basics for bulk blends: critical relative humidity, chemical reactions, size matching, and the fertilizer pairs that should never be mixed.

Written by the Nuroil trade desk, Sharjah

Illustration of a young plant growing in field soil
On this page · 5 sections
  1. 01Three ways a blend can fail
  2. 02Critical relative humidity in practice
  3. 03Physical compatibility: size, density and shape
  4. 04Good blending practice
  5. 05Sourcing blend components

Bulk blending combines straight granular fertilizers, such as urea, DAP, MAP and potash, into a custom N-P-K ratio. It is flexible and economical, but not every pair of materials can share a pile. Some combinations absorb moisture until they turn to slurry, some react chemically, and a few create safety concerns. This guide sets out the basic checks before any blend is made.

Three ways a blend can fail

  • Moisture pick-up. Each fertilizer has a critical relative humidity (CRH): the air humidity above which it absorbs moisture. A blend almost always has a lower CRH than the average of its ingredients, and sometimes far lower, so it becomes sticky, cakes or liquefies in conditions the separate products would tolerate.
  • Chemical reaction. Free acid in some phosphates can break down urea or react with carbonates. Urea and superphosphates can form a sticky urea phosphate compound.
  • Safety. Ammonium nitrate is an oxidiser. Mixing it with combustible or reactive materials, such as elemental sulphur or organic matter, changes the hazard profile of the blend and may change how it is classified.

Critical relative humidity in practice

CRH is normally quoted at 30 °C, and the lower the figure, the more readily a material takes up water. Ammonium nitrate already has a lower CRH than urea, but the real problem appears when the two are combined: the CRH of the mixture collapses to a level that is exceeded in almost any climate. Such a blend picks up moisture very quickly, becomes wet and can turn to slurry, which is why urea and ammonium nitrate must not be dry blended and should be stored well apart. Urea blended with DAP, MAP or potash keeps a much more workable CRH, but still needs dry conditions during blending and storage. CRH also falls slightly as temperature rises, so hot, humid ports need extra care. Commercial products can differ a little from published values for pure salts, depending on impurities and coatings.

PairPractical statusMain reason
Urea + ammonium nitrate (or AN-based NPK)Do not mixVery low blend CRH; mixture wets and forms slurry
Urea + single or triple superphosphateAvoid, or spread immediately after mixingSticky urea phosphate; moisture released into the blend
Ammonium nitrate + elemental sulphurDo not mixSulphur is combustible and can react with nitrates
Phosphates with free acid + urea or carbonatesLimited; check free acidUrea hydrolysis; acid attack on carbonates
Urea + DAP, MAP or potashGenerally compatibleWatch humidity during blending to avoid caking
DAP or MAP + potashGenerally compatibleMatch granule sizes

The table summarises common pairs only. Industry associations publish full compatibility charts with green, yellow and red categories; check the chart and the product SDS before using any unfamiliar component.

Physical compatibility: size, density and shape

Chemically compatible materials can still separate. If the size guide numbers of the components differ by more than about 10, small and large granules segregate during loading, transport and spreading, and the field receives uneven ratios. Differences in particle density and shape make segregation worse. Choose components with similar size ranges and avoid dusty lots.

Good blending practice

  1. Confirm the target analysis and that the formulation complies with local fertilizer regulations.
  2. Check every pair of components against a compatibility chart.
  3. Check moisture, free acid and size data on each component's certificate of analysis.
  4. Blend in dry conditions, ideally below the blend's CRH, and keep blending equipment clean between products.
  5. Apply or bag blends promptly; most blends are not meant for long storage, especially those containing nitrates.
Compatibility is checked pair by pair. One incompatible component is enough to spoil an entire blend.

Sourcing blend components

When buying straights for blending, specify the size range or SGN you need so that components match, and set maximum moisture limits. Ask for a certificate of analysis on each lot. Nuroil supplies urea, DAP and other granular fertilizers with a CoA on every delivery and can share SDS and arrange independent inspection on request. See our urea and DAP pages, or contact us about your blend components.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote