Ferric chloride as a 40% FeCl₃ solution, and anhydrous on request, for coagulating drinking water and wastewater, removing phosphate and conditioning sludge.
Ferric chloride, FeCl₃, is an iron salt sold mainly as a dark brown solution of about 40%. In water it forms iron hydroxide floc that traps suspended solids, colour and organic matter, and binds phosphate as insoluble iron phosphate.
It works over a wide pH range and gives a heavy floc that settles quickly, which makes it a standard coagulant for wastewater, phosphate removal and sludge dewatering. The solution is strongly acidic and corrosive, so it is handled in plastic, rubber-lined or other resistant equipment.
Identity
Formula
FeCl₃
Molar mass
162.20 g/mol
CAS
7705-08-0
Iron(III) chloride · FeCl₃Why Ferric chloride
Heavy, fast-settling flocIron floc is dense and settles quickly, which suits clarifiers under load and high-solids water.
Removes phosphateBinds phosphate as iron phosphate, the standard chemical route to meet discharge limits.
Wide pH rangeWorks from acidic to alkaline water, and helps condition sludge before dewatering.
Documented qualityEach offered batch comes with its Certificate of Analysis and safety data sheet.
What Nuroil does on every order
Why choose ferric chloride from Nuroil?
Checked against the batch CoA
FeCl₃, ferrous iron, free acid and insolubles are reviewed on the batch certificate before loading.
Dangerous-goods paperwork handled
Shipped as class 8 corrosive, UN 2582 solution or UN 1773 anhydrous, with the correct labels.
Acid-resistant packing
HDPE drums, IBCs or rubber-lined tanks for the solution; sealed drums for anhydrous.
One desk, firm offers
FOB, CFR or CIF from our Sharjah trade desk, usually within 24 hours.
02 TECHNICAL DATA
Technical specification.
FeCl₃ (solution)
38–42%, typically 40%Titration
Total iron as Fe (solution)
About 13.5–14.5%Titration / ICP
Ferrous iron (Fe²⁺)
0.5% max, typically far lowerPermanganate titration
Free acid (as HCl)
1% max, typically 0.3–0.5%Titration
Water-insoluble matter
0.2–0.5% maxGravimetric
Density at 20 °C (40%)
1.40–1.44 g/cm³Hydrometer
FeCl₃ (anhydrous)
96–98% minTitration
Appearance
Dark red-brown liquid; anhydrous: black-brown crystalsVisual
Reference standards
EN 888, AWWA B407
0140% SOLUTION
Water treatment
The usual form for drinking water and wastewater: pumped straight from tank or IBC to the dosing point.
02DRINKING-WATER GRADE
Low heavy metals
Solution made to EN 888 or AWWA B407 limits for potable water; confirm the certificate with the offer.
03ANHYDROUS
Concentrated solid
Black-brown crystals of 96–98% FeCl₃, for long-distance shipment, etching and chemical use.
04ETCHING GRADE
Electronics and metal
Solution for etching copper on circuit boards and for photo-engraving.
Selection guidance Tell us the use, the dosing equipment, the distance to your site and any drinking-water certificate required, and we will confirm the form and grade.
Three common coagulants. The right one depends on the water, the pH and the sludge you can handle; a jar test decides.
Property
Ferric chlorideThis page
PAC
Aluminium sulphate
Floc
Heavy, fast-settling
Fast, dense
Light
Phosphate removal
Strong
Good
Good
Working pH range
About 4–11
About 5–9
About 5.5–7.5
Corrosiveness
High
Moderate
Low (solid)
Best suited to
Wastewater, phosphate, sludge, colour
Drinking water, cold or low-alkalinity water
General clarifying at low cost
03 HOW IT IS MADE
From iron and acid to a coagulant.
Scrap iron or iron oxide is dissolved in hydrochloric acid to form ferrous chloride, which is then oxidised with chlorine to ferric chloride. The solution is filtered and adjusted to strength; anhydrous FeCl₃ is made by chlorinating iron directly at high temperature.
01
Iron and acid
Scrap iron or iron oxide is dissolved in hydrochloric acid.
02
Chlorination
The ferrous chloride is oxidised with chlorine to ferric chloride.
03
Adjusting strength
The solution is filtered and set to about 40% FeCl₃.
04
Testing and packing
Each batch is tested for FeCl₃, ferrous iron and free acid, then filled.
04 APPLICATIONS
Where it works.
01
Drinking water
Coagulation of surface water for turbidity, colour and organic matter removal.
02
Sewage treatment
Chemical phosphate removal and better primary settling in municipal plants.
03
Industrial effluent
Removal of solids, heavy metals, oil and sulphide from process effluent.
04
Sludge conditioning
Conditioning sludge ahead of filter presses and centrifuges.
05
Odour control
Binding hydrogen sulphide in sewers and digesters.
06
Etching
Etching copper on circuit boards and metal for engraving.
05 SAFETY & HANDLING
Corrosive. Handle with care.
This summary does not replace the Safety Data Sheet. Review the SDS and site procedure before first handling.
Danger
H290 May be corrosive to metals.
H302 Harmful if swallowed.
H315 Causes skin irritation.
H318 Causes serious eye damage.
UN
2582 solution · 1773 anhydrous
Class
8, corrosive · PG III
01
Protect eyes and skin
It causes serious eye damage and skin irritation; wear goggles, face shield, gloves and apron.
02
Corrosive to metals
Use HDPE, FRP, rubber-lined or PVC equipment; it attacks mild steel, stainless steel and aluminium.
03
Keep from alkalis and hypochlorite
Mixing with strong alkalis is violent; with hypochlorite it can release chlorine gas.
04
It stains
Spills leave rust-brown stains on concrete and clothing; neutralise with lime or soda ash and rinse.
05
Exposure response
Rinse skin or eyes immediately with plenty of water for at least 15 minutes and seek medical attention.
Acid-proof tanks, bunded.
StoreClosed, bunded
The solution is stable when kept closed; anhydrous FeCl₃ absorbs moisture fast and must stay sealed. Confirm the producer’s shelf life with the offer.
Resistant containersHDPE, FRP or rubber-lined tanks, with bunding to hold a spill.
Shaded and ventedOut of direct sun, with tank vents led to a safe place: warm solution gives off acid fumes.
SegregateApart from alkalis, hypochlorite and reactive metals.
Keep anhydrous sealedReseal drums at once: anhydrous FeCl₃ draws moisture and gives off HCl fumes.
Plan documentation early.
HS code2827.39
CAS number7705-08-0
EC number231-729-4
UN numberUN 2582
UN numberUN 1773
GHS
Corrosive to metals; harmful if swallowed; skin irritation; serious eye damage
Transport
Class 8, PG III: UN 2582 solution, UN 1773 anhydrous
Drinking water use
EN 888 or AWWA B407 grade; confirm local approval (for example NSF/ANSI/CAN 60)
National regulations
Confirm the destination’s import and dangerous-goods requirements
06 PACKING OPTIONS
Choose your packing.
Pack sizes and container loads depend on the producer and form; the offer confirms them.
Small quantities
HDPE drums
Solution in UN-approved plastic drums of about 250–300 kg.
Commercial ferric chloride solution is about 40% FeCl₃, typically 38–42%, equal to about 13.8% iron. Compare offers on FeCl₃ or iron content.
02Solution or anhydrous?
Most water plants use the solution, pumped straight to dosing. Anhydrous FeCl₃ is more concentrated and cheaper to ship over long distances, but it must be dissolved carefully, as it gives off heat and HCl fumes.
03Why is ferric chloride used for phosphate removal?
Iron binds phosphate as insoluble iron phosphate, which settles with the sludge. Doses are set by the phosphate load, usually by jar test and plant trial.
04Will it stain or corrode?
Yes. It is acidic and corrosive to most metals and stains concrete and fabric. Use plastic, FRP or rubber-lined equipment and bund the store.
05Is it dangerous goods for shipping?
Yes. The solution ships as UN 2582 and anhydrous as UN 1773, both class 8, packing group III. We prepare the dangerous-goods documents with the shipment.
06What is the HS code?
Ferric chloride is classified under HS 2827.39. Its CAS number is 7705-08-0.
07What documents come with a shipment?
A Certificate of Analysis and Safety Data Sheet, with the Certificate of Origin and dangerous-goods declaration as required.
Include solution or anhydrous, the strength, the use, quantity and destination for a tailored offer. We reply with a firm FOB, CFR or CIF offer, usually within 24 hours.