Calcium chloride as 77% dihydrate flakes or 94–97% anhydrous prills and powder, for raising water hardness, oilfield brines, concrete, dust control and drying.
Calcium chloride, CaCl₂, is a white salt that dissolves readily in water, giving off heat as it does. It is the most soluble common source of calcium, which is why it is used to raise calcium hardness in pools and soft water, and to make the dense, clear brines used in oil and gas wells.
It draws moisture from the air, which makes it a good drying agent and dust suppressant but also means it must be kept sealed. The 77% flakes are the dihydrate; the 94% and above prills and powder are anhydrous and carry more calcium chloride per tonne.
Identity
Formula
CaCl₂
Molar mass
110.98 g/mol
CAS
10043-52-4
Calcium chloride · CaCl₂Why Calcium chloride
Most soluble calciumDissolves fast and completely, so calcium hardness is raised without residue.
Dense, clear brinesMakes solids-free brines of up to about 1.39 g/cm³ for well completion and workover.
Flakes or anhydrous77% flakes for general use; 94% and above prills where strength per tonne and freight matter.
Documented qualityEach offered batch comes with its Certificate of Analysis and safety data sheet.
What Nuroil does on every order
Why choose calcium chloride from Nuroil?
Checked against the batch CoA
CaCl₂, alkali chlorides, magnesium and insolubles are reviewed on the batch certificate before loading.
Strength matched to the job
Flakes, prills or powder chosen for the use, the dissolving method and freight cost.
Packed against moisture
PE-lined bags and jumbo bags, sealed against the humid air it draws in.
One desk, firm offers
FOB, CFR or CIF from our Sharjah trade desk, usually within 24 hours.
02 TECHNICAL DATA
Technical specification.
CaCl₂, flakes (dihydrate)
74% min, typically 77%EDTA titration
CaCl₂, prills or powder (anhydrous)
94% min; 95–97% on many offersEDTA titration
Alkali chlorides (as NaCl)
1–5% max, by gradeFlame photometry / ICP
Magnesium chloride (MgCl₂)
0.5% maxEDTA titration
Calcium hydroxide (Ca(OH)₂)
0.25% maxTitration
Water-insoluble matter
0.25% maxGravimetric
Iron (Fe)
0.006% maxICP / colorimetric
pH (5% solution)
7.5–11pH meter
Appearance
White flakes, prills, granules or powderVisual
Reference standard
ASTM D98
0177% FLAKES
General use
Dihydrate flakes, the economical form for water hardness, dust control, concrete and de-icing.
0294% PRILLS
Strongest, low dust
Anhydrous prills of 2–6 mm: more CaCl₂ per tonne, free-flowing and low in dust.
0394% POWDER
Fast dissolving
Anhydrous powder for quick make-up of brines and for drying and chemical use.
04BRINE GRADE
Oilfield
Low-insoluble anhydrous grades for clear completion and workover brines.
Selection guidance Tell us the use, how you dissolve or spread it, and the strength or purity your process needs, and we will confirm the grade and form.
The same chemical at two strengths. The right one depends on the use, how you dissolve it and freight cost.
Property
77% flakes
94% prills
94% powder
CaCl₂ content
74–77%
94–97%
94–97%
Heat on dissolving
Moderate
High
High
Dust
Some
Low
More
CaCl₂ per tonne shipped
Lower
Higher
Higher
Best suited to
Water hardness, dust control, concrete
Brines, de-icing, low-dust handling
Fast make-up, drying, chemicals
03 HOW IT IS MADE
From limestone and brine to dry flakes.
Calcium chloride comes from limestone dissolved in hydrochloric acid, from natural brines, or as a co-product of soda ash making. The purified solution is evaporated, then flaked to the dihydrate or dried further and prilled or ground to the anhydrous grades.
01
Limestone and acid
Limestone is reacted with hydrochloric acid, or brine is drawn and purified.
02
Purifying
Magnesium, iron and sulphate are removed from the calcium chloride solution.
03
Evaporating and forming
The solution is concentrated, then flaked, prilled or dried to powder.
04
Testing and packing
Each batch is tested for CaCl₂ and impurities, then sealed in lined bags.
04 APPLICATIONS
Where it works.
01
Water hardness
Raising calcium hardness in soft or desalinated water and in pools, to protect pipes and plaster.
02
Oilfield brines
Clear completion and workover brines, and drilling-fluid additive.
03
Concrete
Accelerating set in plain concrete; not for reinforced concrete where chloride limits apply.
04
Dust control
Holding moisture on unpaved roads and site tracks to keep dust down.
05
Drying and humidity
Desiccant for air, gases and moisture absorbers in containers.
06
Industry and food
Chemical processing, refrigeration brines, and food use in certified food grade only.
05 SAFETY & HANDLING
An irritant. Mind the heat.
This summary does not replace the Safety Data Sheet. Review the SDS and site procedure before first handling.
Warning
H319 Causes serious eye irritation.
UN
Not regulated
Transport
Not dangerous goods
01
Protect the eyes
It causes serious eye irritation; wear goggles when handling solid or brine.
02
It gets hot
Dissolving releases a lot of heat, the anhydrous grade most; add it slowly to cool water with stirring.
03
Gloves for long contact
It dries and irritates skin; wear gloves and wash off spills.
04
Corrodes some metals
Wet calcium chloride and brines corrode steel and aluminium; rinse equipment after use.
05
Exposure response
Rinse eyes with plenty of water for several minutes and seek medical attention if irritation persists.
Dry and sealed.
Shelf lifeLong, if sealed
Calcium chloride does not degrade, but it draws moisture from the air, cakes and finally dissolves if left open. Kept sealed and dry it keeps for years. Confirm the producer’s shelf life with the offer.
Keep bags sealedIt is strongly hygroscopic; reseal opened bags at once.
Dry, covered storeOn pallets, off the floor and away from humid air and rain.
SegregateApart from zinc, aluminium and reactive metals, and from strong acids.
First in, first outUse the oldest stock first before moisture starts to cake it.
Plan documentation early.
HS code2827.20
CAS number10043-52-4
EC number233-140-8
TransportNot regulated
GHS
Causes serious eye irritation
Transport
Not regulated as dangerous goods
Product standard
ASTM D98 for calcium chloride; food use only in certified food grade (E509)
National regulations
Confirm the destination’s import requirements and any drinking-water approval
06 PACKING OPTIONS
Choose your packing.
Pack sizes and container loads depend on the producer and grade; the offer confirms them.
Smaller orders
25 kg lined bags
PP woven bags with a PE liner, palletised, the usual export packing.
01What is the difference between 77% and 94% calcium chloride?
The 77% flakes are the dihydrate, carrying two molecules of water; the 94% and above grades are anhydrous. Anhydrous gives more CaCl₂ per tonne and more heat on dissolving.
02How is it used in water treatment?
To raise calcium hardness in soft or desalinated water and in pools, which protects pipes, plaster and equipment from aggressive water.
03How heavy a brine can it make?
Calcium chloride brines reach about 1.39 g/cm³ (about 11.6 lb/gal) at saturation, depending on temperature. Heavier brines blend it with calcium bromide.
04Can it be used in concrete?
It speeds setting in plain concrete. Its chloride attacks steel, so most codes forbid it in reinforced and prestressed concrete.
05Is it dangerous goods for shipping?
No. Calcium chloride is not regulated as dangerous goods. It causes eye irritation and is labelled accordingly.
06What is the HS code?
Calcium chloride is classified under HS 2827.20. Its CAS number is 10043-52-4 (anhydrous); the dihydrate is 10035-04-8.
07What documents come with a shipment?
A Certificate of Analysis and Safety Data Sheet, with the Certificate of Origin as required.
Include the grade (77% flakes or 94% prills or powder), the use, packing, quantity and destination for a tailored offer. We reply with a firm FOB, CFR or CIF offer, usually within 24 hours.