Hydrated lime, also called slaked lime, is calcium hydroxide, Ca(OH)₂: a fine white powder made by adding water to quicklime. It is a strong, low-cost alkali that raises pH and adds calcium to water.
Water plants use it to correct pH and alkalinity, to soften hard water by precipitating calcium carbonate, and, with carbon dioxide, to put back the hardness desalinated water lacks. It is dosed as a slurry or as clear lime water from a saturator. It is only slightly soluble, so dosing equipment is built to handle a suspension.
Identity
Formula
Ca(OH)₂
Molar mass
74.09 g/mol
CAS
1305-62-0
Calcium hydroxide · Ca(OH)₂Why Hydrated lime
Low-cost alkaliRaises pH and alkalinity at a lower cost per unit of alkalinity than caustic soda or soda ash.
Adds calciumPuts calcium hardness back into desalinated and soft water, which protects pipes from corrosion.
Softens and settlesPrecipitates calcium carbonate and magnesium hydroxide, helping remove hardness, metals and phosphate.
Documented qualityEach offered batch comes with its Certificate of Analysis and safety data sheet.
What Nuroil does on every order
Why choose hydrated lime from Nuroil?
Checked against the batch CoA
Ca(OH)₂, available CaO, insolubles and fineness are reviewed on the batch certificate before loading.
Grade matched to the use
High-calcium, drinking-water grade for potable water; standard grades for effluent and industry.
Packed to stay dry
Lined bags that keep out moisture and carbon dioxide, which slowly turn lime to chalk.
One desk, firm offers
FOB, CFR or CIF from our Sharjah trade desk, usually within 24 hours.
02 TECHNICAL DATA
Technical specification.
Calcium hydroxide (Ca(OH)₂)
90% min; 95–97% on high-calcium gradesTitration (EN 459-2 / ASTM C25)
Available calcium oxide (CaO)
68% min, typically 70–73%Sugar method (ASTM C25)
Magnesium oxide (MgO)
1–2% maxEDTA titration / ICP
Carbon dioxide (CO₂)
2–3% maxGravimetric / gasometric
Acid-insoluble matter
1% maxGravimetric
Iron oxide (Fe₂O₃)
0.1–0.3% maxICP / colorimetric
Fineness
90% min passing 75 µm (200 mesh)Wet sieve
Appearance
Fine white powderVisual
Reference standards
AWWA B202, EN 12518
01DRINKING-WATER GRADE
Potable water
High-calcium lime meeting AWWA B202 or EN 12518 limits, for pH correction and remineralisation.
02HIGH CALCIUM 95%+
Clear lime water
Low-insoluble lime for saturators, where grit and residue must be kept down.
03STANDARD 90%
Effluent and industry
Economical grade for neutralising acid effluent, sludge treatment and construction.
04SLURRY ON REQUEST
Milk of lime
Ready-made lime slurry for nearby plants without slaking or make-up equipment.
Selection guidance Tell us the use (pH correction, softening, remineralisation or effluent), the dosing equipment and any drinking-water certificate required, and we will confirm the grade.
Three alkalis for raising pH. The right one depends on whether you also want calcium, and on the dosing you can run.
Property
Hydrated limeThis page
Caustic soda
Soda ash
Cost per unit of alkalinity
Lowest
Higher
Moderate
Adds calcium hardness
Yes
No
No
Solubility
Low, dosed as slurry
Very high
High
Handling
Dusty powder, slurry
Corrosive liquid or solid
Dry, easy
Best suited to
Remineralisation, softening, effluent
Precise pH control
Alkalinity without calcium
03 HOW IT IS MADE
From limestone to fine powder.
Limestone is burnt in a kiln at about 900–1,100 °C, driving off carbon dioxide to leave quicklime. The quicklime is slaked with a measured amount of water in a hydrator, then air-classified to a fine, dry powder.
01
Limestone
High-calcium limestone is quarried, crushed and screened.
02
Burning
The limestone is calcined in a kiln to quicklime, releasing CO₂.
03
Slaking
Quicklime is hydrated with water and classified to a fine powder.
04
Testing and packing
Each batch is tested for Ca(OH)₂, available CaO and fineness, then packed.
04 APPLICATIONS
Where it works.
01
Remineralisation
With carbon dioxide, restoring hardness and alkalinity to desalinated water.
02
pH correction
Raising the pH of drinking water after coagulation to limit corrosion.
03
Softening
Lime softening of hard water, removing calcium and magnesium as precipitate.
04
Effluent neutralising
Neutralising acid effluent and precipitating metals as hydroxides.
05
Sludge treatment
Stabilising and conditioning sewage sludge.
06
Construction and industry
Mortar, plaster and soil stabilisation, and chemical processes.
05 SAFETY & HANDLING
Strongly alkaline. Protect the eyes.
This summary does not replace the Safety Data Sheet. Review the SDS and site procedure before first handling.
Danger
H315 Causes skin irritation.
H318 Causes serious eye damage.
H335 May cause respiratory irritation.
UN
Not regulated
Transport
Not dangerous goods
01
Eye protection first
Lime dust causes serious eye damage; wear sealed goggles when handling powder or slurry.
02
Control dust
It irritates skin and the respiratory tract: use dust extraction or a dust mask, gloves and long sleeves.
03
Keep from acids
It reacts with acids, giving off heat; add it slowly to acidic effluent with mixing.
04
Wash skin promptly
Wet lime on skin can cause burns over time; wash off with water.
05
Exposure response
Rinse eyes immediately with plenty of water for at least 15 minutes and seek medical attention.
Dry and sealed.
Shelf lifeAbout 6–12 months
Lime slowly absorbs carbon dioxide from the air and turns to calcium carbonate, losing strength. Kept dry in sealed bags it holds its quality for months. Confirm the producer’s shelf life with the offer.
Keep bags sealedAir and moisture slowly carbonate lime; reseal opened bags.
Dry, covered storeOn pallets, off the floor and under cover from rain.
SegregateApart from acids and from ammonium salts, which release ammonia with lime.
First in, first outUse the oldest stock first so it is dosed at full strength.
01What is the difference between hydrated lime and quicklime?
Quicklime is calcium oxide, CaO, straight from the kiln; it reacts with water and heats strongly. Hydrated lime is quicklime already slaked with water, Ca(OH)₂: a stable, fine powder that is easier to store and dose.
02What does available CaO mean?
The share of the lime that is active as calcium oxide or hydroxide. AWWA B202 has long based hydrated lime on 68% available CaO, about 90% Ca(OH)₂. Higher figures mean less product for the same dose.
03How is it dosed?
As a slurry, milk of lime, from a mixing tank, or as clear lime water from a saturator where a clean, residue-free feed is needed.
04Why use lime for desalinated water?
Desalinated water has almost no calcium or alkalinity and corrodes pipes. Lime with carbon dioxide adds both back, giving a stable, less corrosive water.
05Is it dangerous goods for shipping?
No. Hydrated lime is not regulated as dangerous goods, but it causes serious eye damage, so it is labelled and handled with care.
06What is the HS code?
Hydrated lime is classified under HS 2522.20. Its CAS number is 1305-62-0.
07What documents come with a shipment?
A Certificate of Analysis and Safety Data Sheet, with the Certificate of Origin and any drinking-water certificate as required.
Include the grade or Ca(OH)₂ content, the use, packing, quantity and destination for a tailored offer. We reply with a firm FOB, CFR or CIF offer, usually within 24 hours.