Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Urea & fertilizers

Prilled vs granular urea: what is the difference?

Prilled and granular urea share the same chemistry but differ in size, strength and handling. Here is how to choose between them.

Written by the Nuroil trade desk, Sharjah

Illustration of urea granules and bagged fertilizer
On this page · 5 sections
  1. 01How each form is made
  2. 02Size and strength
  3. 03Which form suits which use
  4. 04Handling and storage points
  5. 05What to specify

Urea is sold in two main solid forms: prilled and granular. Both contain about 46% nitrogen and have the same chemical make-up. What differs is how the particles are formed, and that affects their size, strength, dust levels and how well they survive handling and spreading. Choosing the right form depends on how the product will be shipped, stored and used.

How each form is made

01

Prilling

sprays concentrated molten urea from the top of a tall tower. Droplets fall through a rising stream of cooling air and solidify into small, round prills. The height of the tower largely limits how big the prills can grow, so they are relatively small.
02

Granulation

builds particles up in layers. Urea solution is sprayed onto small seed particles in a fluidised bed or drum, and each pass adds a thin coat. Because size is controlled by residence time rather than fall height, granules can be made larger and denser.

In both processes producers often add a small amount of formaldehyde-based conditioner to improve particle strength and reduce caking.

Size and strength

Producer specifications commonly quote prilled urea with most particles between about 1 and 3.5 mm, and granular urea with most between about 2 and 4.5 mm. A published comparison of plant samples found prills averaging around 1.65 mm and granules close to 3 mm.

The same study measured crushing strength by pressing single particles. Prills failed at an average of about 3.8 newtons, while granules withstood roughly 10 to 17 newtons. Prills, however, were more uniform in size and strength. Larger prills can also contain a small internal void, which weakens them.

PropertyPrilled ureaGranular urea
Nitrogen contentAbout 46%About 46%
Typical size rangeAbout 1 to 3.5 mmAbout 2 to 4.5 mm
Crushing strengthLowerHigher
Dust and fines from handlingMore likelyLess likely
Dissolving speedFasterSlightly slower

Which form suits which use

Granular urea is generally preferred for:

  • Bulk ocean shipping and multiple handling steps, where weak particles break into dust.
  • Bulk blending with other granular fertilizers, because matched particle sizes reduce segregation in the blend.
  • Mechanical broadcast spreading, where larger, stronger particles hold up better in the spreader and are less likely to break into fines that drift.

Prilled urea remains widely used for:

  • Hand application and small farms, where the small particle size spreads evenly by hand.
  • Dissolving in water for foliar sprays, fertigation or liquid feeds, where smaller particles dissolve quickly.
  • Industrial and technical uses where the urea will be dissolved or melted anyway.
The nitrogen is the same; the choice comes down to how much handling the product must survive and how it will be applied.

Handling and storage points

Both forms absorb moisture from humid air and can cake. Prills, being weaker and smaller, are more prone to breakage and dust after repeated handling, which can worsen caking in stockpiles. Granules handle better in bulk but still need dry, covered storage. Neither form should be mixed or stored in contact with ammonium nitrate, as the two together become very hygroscopic.

For bulk cargoes, it is worth agreeing how particle size will be checked at loading and discharge. A sieve analysis on representative samples shows whether the product still meets the size band after loading, and a crushing-strength figure from the producer gives an idea of how much breakage to expect over a long voyage and several transfers.

What to specify

When enquiring for urea, state the form (prilled or granular), required size range, nitrogen minimum, biuret and moisture limits, and whether you need an anti-caking conditioner or a conditioner-free product for technical use. Add packing (bulk, 50 kg bags or jumbo bags) and destination. Ask for a certificate of analysis for each lot and, if needed, an independent inspection of size distribution at loading. Nuroil can quote both forms from established producers for agricultural and technical use.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote