Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read7 sections

Knowledge centre · Caustic soda & soda ash

Diluting 50% caustic soda lye on site

How to calculate water for diluting 50% caustic soda lye, why volumes are not additive, and how to manage heat and splashing safely.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of a tanker delivering caustic soda lye
On this page · 8 sections
  1. 01The calculation
  2. 02Water volume = V × SG × (B − C) ÷ C
  3. 03Why the final volume is smaller than you expect
  4. 04Heat of dilution
  5. 05The safe order: caustic into water
  6. 06Water quality and equipment
  7. 07Protective equipment and emergency provision
  8. 08Buying for dilution

Many plants buy caustic soda lye at 50% and dilute it to 20–32% for dosing or to keep it from freezing. Dilution looks simple, but it releases heat, the volumes do not add up neatly, and getting the order wrong can cause violent boiling. This article covers the calculation and the safe procedure.

The calculation

Producer handbooks give a simple formula for the volume of water needed:

Water volume = V × SG × (B − C) ÷ C

  • V is the volume of strong lye.
  • SG is the specific gravity of the strong lye (about 1.53 for 50% caustic soda at 15.6 °C).
  • B is the strength of the strong lye (% NaOH by weight).
  • C is the target strength (% NaOH by weight).

Example: to take 10 m³ of 50% lye down to 32%, water = 10 × 1.53 × (50 − 32) ÷ 32, which is about 8.6 m³. The 10 m³ of lye weighs about 15.3 t and holds about 7.7 t of NaOH; the finished batch weighs about 24 t at 32%.

Why the final volume is smaller than you expect

When caustic soda and water mix, the volumes are not additive. In the example, 10 m³ plus 8.6 m³ does not give 18.6 m³; the result is slightly less. To find the true final volume, work in weights and divide the total by the density of the diluted solution from the supplier's density table. This matters when sizing a dilution tank and when calibrating level gauges in tonnes of NaOH.

Heat of dilution

Mixing strong caustic with water releases significant heat. Producers even use this effect to make warm caustic for passivating steel tanks: diluting 50% to 20% raises the temperature noticeably. On a large batch the rise can push the solution well above the temperature that carbon steel and some plastics tolerate. Plan for it:

  • Check the temperature limits of the dilution tank, pipework and any lining.
  • Add lye in stages and monitor temperature, allowing time to cool between additions if needed.
  • Use a recirculation loop or mixer so heat does not concentrate at one point.

The safe order: caustic into water

Always add caustic soda to water, never water to caustic soda.

Safety data sheets for 50% lye are explicit on this point. If water is added to strong caustic, the heat is released in a thin layer at the surface, which can boil and throw out hot corrosive liquid. Charge the water first, start the agitator, then add lye slowly below the surface where possible. One producer's SDS also advises using lukewarm dilution water rather than hot or very cold water.

Water quality and equipment

  • Softened water is recommended for dilution: hard water forms calcium and magnesium scale that blocks dosing lines and injectors.
  • Materials: dilution tanks in stainless steel, lined steel, polyethylene or polypropylene are common; never aluminium, zinc, copper or their alloys, which caustic attacks and which can release hydrogen.
  • Venting: never seal a vessel during dilution.
  • Check the result by titration or a density reading at a known temperature before putting the batch into service.

Protective equipment and emergency provision

Wear close-fitting chemical goggles with a face shield, long rubber or PVC gloves with sleeves over the cuffs, a chemical-resistant suit or apron, and rubber boots with trousers outside them. Caustic destroys leather. A safety shower and eyewash must be at hand and tested before the job. Read the product SDS before starting.

Buying for dilution

If you dilute on site, buy the strongest grade that your climate and storage can handle, and ask the supplier for the actual concentration on the certificate of analysis so your water calculation is right. Nuroil provides a CoA with every lye delivery; enquire through request a quote.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote