Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Caustic soda & soda ash

Safe handling, protective equipment and dissolving of caustic soda

Reference guide to handling caustic soda safely: hazards, PPE, the right way to dissolve flakes and pearls, first aid and spills.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of caustic soda flakes and pearls
On this page · 6 sections
  1. 01Understanding the hazards
  2. 02Personal protective equipment
  3. 03Dissolving flakes and pearls safely
  4. 04First aid
  5. 05Spills and clean-up
  6. 06Documents to request from your supplier

Caustic soda is one of the most widely used industrial chemicals and one of the most dangerous to handle carelessly. Solid or liquid, it causes severe burns to skin and eyes, and dissolving it releases enough heat to boil water locally. This guide summarises good practice. It does not replace the product safety data sheet (SDS), which should be read before work begins.

Understanding the hazards

  • Corrosive to tissue. Caustic soda attacks skin, eyes and mucous membranes. Even dilute solutions can damage tissue after prolonged contact, and burns may not hurt immediately.
  • Dust and mist. Dust from flakes or pearls and mist from solutions irritate and damage the respiratory tract. Occupational limits are low, around 2 mg/m³ in several jurisdictions.
  • Heat of solution. Dissolving solid caustic, or diluting strong solutions, releases a large amount of heat. Contact with water can even generate enough heat to ignite nearby combustible material.
  • Reactivity. Caustic soda reacts with acids and attacks aluminium, zinc and tin, producing flammable hydrogen gas. Keep it away from these metals and from acids.

Personal protective equipment

Body areaRecommended protection
Eyes and faceClose-fitting chemical splash goggles at all times; add a face shield where splashing is possible, such as loading, unloading and dissolving
HandsRubber, PVC or other alkali-resistant gloves long enough to extend above the wrist, with sleeves worn over the glove cuffs
BodyChemical-resistant clothing such as a rubber or vinyl suit or apron
FeetRubber boots with trouser legs worn outside, not tucked in; caustic quickly destroys leather
BreathingAn approved particulate respirator where dust or mist may exceed exposure limits

Eyewash stations and safety showers should be installed wherever caustic is handled, and checked regularly.

Dissolving flakes and pearls safely

  1. Use a vessel made of a suitable material, such as steel, stainless steel or a rated plastic, with enough capacity and freeboard. Never use aluminium or galvanised containers.
  2. Start with water, not caustic. Producers recommend lukewarm water of roughly 27 to 38 °C; very cold or hot water increases the risk of violent boiling.
  3. Start agitation first. A propeller mixer or a recirculating pump is preferred. Avoid air sparging, which pulls in carbon dioxide and forms carbonate.
  4. Add the caustic slowly to the surface of the moving water, a little at a time, and let it dissolve before adding more.
  5. Never add water to caustic soda. Never dump a whole bag into still water: the solids sink, form a slow-dissolving layer at the bottom and can then overheat and erupt.
  6. Allow for the temperature rise. Strong solutions can become hot enough to exceed the limits of plastic tanks, so cooling may be needed.

The same rule applies when diluting 50% lye: add the lye to water, slowly and with mixing.

First aid

  • Eyes: flush immediately with plenty of clean water for at least 15 minutes, holding the eyelids apart. Do not use any neutralising solution. Get medical attention immediately.
  • Skin: remove contaminated clothing and footwear and flush with water for at least 15 minutes. Get medical attention.
  • Inhalation: move the person to fresh air and seek medical help if breathing is affected.
  • Swallowing: do not induce vomiting. Rinse the mouth, give water if the person is conscious, and get medical attention immediately.

Spills and clean-up

Stop the source if it is safe to do so and contain the spill. Sweep up solids carefully without raising dust and place them in dry, labelled containers. Contain liquid spills and recover them into suitable containers. Residues can then be neutralised cautiously with a dilute acid and flushed with water, in line with the SDS and local rules. Keep spilled caustic out of drains and waterways.

Goggles always, caustic into water and never the reverse, and fifteen minutes of flushing for any splash.

Documents to request from your supplier

Ask for a current SDS in the language your site uses, product labelling consistent with transport and hazard rules, and a certificate of analysis for each lot. Make sure your enquiry states the packing you can handle safely, such as 25 kg bags rather than larger units if you dose by hand. Nuroil supplies the SDS with caustic soda shipments and can answer handling questions through contact us.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote