Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read6 sections

Knowledge centre · Waterproofing & construction

Why cold asphalt patches fail and how to prevent it

Ravelling, dishing, shoving, pushing out and stripping: the common ways cold asphalt patches fail, what causes each and the fix.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of a cold-applied roadway repair
On this page · 6 sections
  1. 01The main failure types
  2. 02Material problems
  3. 03Preparation and placement problems
  4. 04Underlying pavement problems
  5. 05Hot-climate failures
  6. 06Specifying to reduce failures

Cold asphalt patches can last for years, but many do not survive the first season. When a patch fails, the cause is usually one of a small number of problems: the wrong material, poor preparation, poor compaction or a hole that was really a symptom of a deeper failure. Recognising the failure pattern tells you which one it was.

The main failure types

What you seeLikely causePrevention
Patch sinks below the road surface (dishing)Too little compaction, too thin a lift, no overfillOverfill slightly, compact in layers, re-check after traffic
Stones loosen and scatter (ravelling)Weak binder film, binder lost through stripping, poor cohesionUse material with good coating and cohesion; compact thoroughly
Patch pushed out of the hole or shoved sidewaysBinder too soft, high temperatures, heavy braking or turning trafficChoose a product rated for the climate and traffic; give square edges for confinement
Patch lifts out in one pieceNo bond to sides and base: dust, water or loose material left in holeClean the hole, remove water, tack the edges
Bare stone and brown water around patchStripping: water displaces binder from the aggregateMaterial with antistrip additive and good coating; drain the hole
Cracks around the edge, water entryFeathered or crumbling edges, no edge sealCut back to sound material; seal edges where water is a concern
Patch stays soft and marks under tyresSolvent not yet evaporated, very thick lift, hot weatherPlace in thinner lifts, allow curing, choose a stiffer product for heat

Material problems

A cold mix has to stay loose for months yet become firm in the hole. Products that are too stiff are hard to place and compact; products that are too soft never gain enough strength. Highway research has highlighted three common material shortcomings: stripping of binder from the stone in stockpiles, instability in hot weather and loss of workability in winter. Field trials found that patch life depended more on material quality than on how carefully the patch was placed, so choosing a good product is the first defence against failure.

Preparation and placement problems

  • Water in the hole. Water stops the binder bonding and, in emulsion mixes, slows curing. Sweep or blow it out where possible.
  • Loose material and dust. The patch bonds to dust, not to the road. Remove it.
  • Thick single lifts. Deep holes filled in one go cannot be compacted to the bottom and may stay soft. Place in layers.
  • No compaction. Relying on traffic alone gives poor density, especially at the edges where tyres rarely pass. Use a plate compactor, roller or vehicle wheels, and leave a slight crown.

Underlying pavement problems

Potholes form when water weakens the pavement and traffic breaks out the damaged material. If the base below is saturated or the surrounding asphalt is badly cracked, a new patch sits on a weak foundation and will fail however good it is. Repeated failures in the same place are a sign that the area needs deeper repair, such as full-depth patching or drainage improvement, and that cold asphalt is only buying time.

Hot-climate failures

In regions with very high pavement temperatures, the most common failure is not cracking but softening. A binder that is ideal for cold, wet repairs may shove, rut or bleed under summer sun and heavy vehicles. Ask for products designed for high temperatures and avoid patching heavy-braking areas, such as junction approaches, with soft material if a hot-mix repair is possible.

When a patch fails, look at where and how. Dishing points to compaction, ravelling and stripping point to material, and repeated failure points to the road beneath.

Specifying to reduce failures

When ordering, describe the traffic, climate, typical hole depth and the season of use, and ask the supplier for workability, stripping resistance and strength data, shelf life and recommended placement method. Nuroil supplies ready-to-use cold asphalt; send your requirements through request a quote.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote