Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article4 min read6 sections

Knowledge centre · Waterproofing & construction

What HPMC does in tile adhesives and dry-mix mortars

How hydroxypropyl methylcellulose keeps water in cement mortars, extends open time and stops tiles slipping, and what to check when buying it.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of a roof being waterproofed with bitumen membrane
On this page · 6 sections
  1. 01Keeping water where the cement needs it
  2. 02Open time and adjustability
  3. 03Slip resistance and workability
  4. 04How HPMC fits with other additives
  5. 05Common problems linked to the cellulose ether
  6. 06What to specify when buying HPMC

Hydroxypropyl methylcellulose, usually shortened to HPMC, is a water-soluble cellulose ether made by chemically modifying plant cellulose. It is added to factory-made dry-mix products such as cementitious tile adhesives, renders, skim coats, self-levelling compounds and masonry mortars. It is only a small part of the formulation by weight, yet it has a large effect on how the mortar behaves on site. Without it, most modern thin-bed tile adhesives would not work.

Keeping water where the cement needs it

The main job of HPMC is water retention. A thin bed of adhesive spread on a porous block wall or onto the back of an absorbent tile can lose much of its mixing water within minutes. The cement then cannot hydrate properly, and the bond is weak, powdery and prone to cracking. Cellulose ethers limit how fast water is drawn out of the fresh mortar into the substrate and into the air.

Exactly how they do this is still studied. Laboratory work using NMR measurements found that cellulose ethers do not noticeably slow the movement of individual water molecules, so the simple idea of a polymer barrier does not fully explain it. Researchers point instead to the way HPMC changes the consistency and structure of the fresh paste. Whatever the mechanism, comparison studies on ordinary dry-mixed mortar have found HPMC to have a stronger effect on water retention and consistency than other common admixtures such as starch ethers.

Open time and adjustability

Open time is the period after the adhesive is combed out during which a tile can still be bedded and reach the required bond. Under the European tile adhesive standard EN 12004, open time is tested to EN 1346. A standard adhesive is expected to keep adequate bond after about 20 minutes, and an adhesive marked E (extended open time) after about 30 minutes. Good water retention is what makes those figures achievable on hot, dry or windy sites, because the surface of the bed does not skin over as quickly.

HPMC also extends adjustment time, the short window in which a tiler can slide a tile into line without breaking the bond.

Slip resistance and workability

The second job is rheology. HPMC thickens the mix so that a bed of adhesive holds its ribbed shape and a tile pressed onto a vertical wall does not slide down. Adhesives classed T under EN 12004 (reduced slip) depend on this. Grades with higher viscosity generally give more body and sag resistance. Lower-viscosity grades are used where flow matters more, as in self-levelling products.

The polymer also makes the mortar smoother and creamier to trowel, and it helps the mix stay uniform rather than bleeding water. Some grades are surface treated so they disperse without lumps and thicken more slowly once water is added. This is useful in machine-mixed and bagged products.

How HPMC fits with other additives

HPMC is rarely used alone. A typical cement-based tile adhesive combines cement, graded sand, HPMC and, in higher classes, a redispersible polymer powder for extra adhesion and flexibility. EN 12004 sets minimum tensile adhesion of 0.5 N/mm² for a normal C1 adhesive and 1.0 N/mm² for an improved C2 adhesive. HPMC helps a mix reach those values by letting the cement hydrate properly. The polymer powder is usually what lifts a product into the C2 or deformable S1 and S2 classes.

PropertyRole of HPMCWhat the site sees
Water retentionLimits water loss to substrate and airProper cement cure, fewer weak or powdery beds
Open timeDelays skinning of the adhesive bedMore time to place tiles, especially in heat
Sag and slip resistanceThickens the pasteRibs hold shape, wall tiles stay put
WorkabilityLubricates and stabilises the mixEasier troweling, less bleeding
HPMC does not make an adhesive strong on its own. It gives the cement the water and time it needs to become strong.

Common problems linked to the cellulose ether

  • Too little or the wrong grade: short open time, poor bond on absorbent backgrounds, tiles slipping.
  • Too much or too high a viscosity: sticky, heavy mortar that is hard to comb and may delay setting.
  • Poor dispersion: lumps or "fish eyes" in the mix, often from a grade unsuited to the mixing method.

Formulators usually test a few grades in their own mix, because sand, cement and climate all affect the result.

What to specify when buying HPMC

For a construction-grade cellulose ether, an enquiry should state the intended use (tile adhesive, render, putty or self-levelling), the viscosity range and the method used to measure it (for example Brookfield or another method, at a stated concentration and temperature). It should also say whether a surface-treated grade is needed, plus moisture content, particle size and packing. Ask for a technical data sheet and a certificate of analysis for each batch, and an SDS for safe handling of the fine powder. Nuroil supplies construction chemicals from established producers with a CoA on every delivery. Send your grade and quantity through a quote request, or see the construction chemicals page.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote