Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Industrial chemicals

Why LABSA 96% darkens and how its colour affects the finished detergent

What the Klett colour of LABSA measures, why the acid can darken in storage or processing, and why colour matters for detergent makers.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of caustic soda flakes and pearls
On this page · 5 sections
  1. 01How colour is measured
  2. 02Where the colour comes from
  3. 03Darkening during neutralisation
  4. 04Keeping colour under control in your plant
  5. 05What to put in your enquiry

Fresh LABSA 96% is a brown, viscous liquid, and its shade varies from lot to lot. For a maker of clear liquid detergents or white washing powder, that shade matters: a dark acid can mean extra bleaching, a slightly off-colour product, or more dye to mask it. This article explains how LABSA colour is measured, what causes it, and how to keep it from getting worse in your plant.

How colour is measured

LABSA colour is usually reported as a Klett value. The acid is diluted to a solution containing 5% active matter and read in a Klett colorimeter; the higher the number, the darker the sample. Measuring a dilute solution rather than the neat acid gives a stable, comparable figure that relates directly to how the surfactant will look once it is diluted in a product.

Commercial specifications for 96% material commonly set a maximum somewhere between about 40 and 50 Klett, and some producers offer lighter grades for premium liquids. Because the method and limit vary, the specification in your contract should state both.

Where the colour comes from

LABSA is made by reacting linear alkylbenzene with sulphur trioxide, usually in a falling-film reactor, then ageing and stabilising the acid. Several things during and after that process influence colour:

  • Side products of sulphonation. Research on falling-film sulphonation reports that sulphones and anhydrides form alongside the main product. Ageing and a small addition of water convert most anhydrides back, but sulphones are hard to remove once formed, so reactor conditions set a baseline colour.
  • Quality of the alkylbenzene feed. Impurities in the feedstock carry through into the acid.
  • Heat after production. Holding the acid hot for long periods, or heating it locally with steam coils, tends to darken it.
  • Contamination. Water ingress makes the acid more corrosive to steel, and the corrosion products can affect colour.

Darkening during neutralisation

The biggest colour change often happens in the customer's own vessel. LABSA contains a small amount of free sulphuric acid, and when strong alkali is added quickly, the reaction with that sulphuric acid releases a lot of heat in a small area. Detergent process patents describe how this can decompose some of the sulphonate and give a dark product. The practical remedies are:

  • add the acid slowly into dilute, well-stirred alkali;
  • keep the batch temperature within the range your formulation allows;
  • avoid neutralising acid that has been sitting in a hot line or drum.
ProductWhy colour matters
Clear or transparent liquid detergentColour shows directly in the bottle; light acid avoids extra dye or bleach
Coloured or opaque liquidModerate colour is usually masked
White spray-dried powderDark sulphonate can tint the powder
Industrial cleanersColour is rarely critical; active matter and free oil matter more

Keeping colour under control in your plant

  • Store LABSA in clean, dry stainless steel, lined or plastic containers and keep lids and vents closed against humid air.
  • Use the oldest stock first and avoid long storage, especially in hot warehouses.
  • If the acid must be warmed to pump it, use gentle, controlled heat rather than direct steam on the drum wall.
  • Check Klett colour on arrival and again before use if stock has been held for a long time, so you can separate supplier variation from storage effects.
Klett colour is set largely at the producer, but heat and fast neutralisation in the customer's plant can make it noticeably worse.

What to put in your enquiry

State the maximum Klett colour you need, the measurement basis (5% active solution is common), and whether the acid is going into clear liquids, coloured liquids or powder. Ask for a CoA with colour, active matter, free sulphuric acid and free oil for each lot. Nuroil supplies a CoA with every delivery and can arrange third-party inspection on request; use our quote form to share your specification.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote