Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Industrial chemicals

Technical-grade urea specifications by end use

Which urea parameters matter for resins, DEF / AUS 32, NOx reduction and other industrial uses, with a comparison table for writing a purchase spec.

Written by the Nuroil trade desk, Sharjah

Illustration of Nuroil technical grade urea at a chemical plant
On this page · 6 sections
  1. 01The core parameters
  2. 02Comparison by end use
  3. 03Solid or solution
  4. 04Other industrial uses
  5. 05Testing and documents
  6. 06Turning this into an enquiry

Technical or industrial-grade urea is not a single specification. The parameters that matter for a resin plant differ from those for a DEF / AUS 32 blender or a power station running SNCR. Buying the right product means matching the specification to the end use rather than copying a generic sheet. This guide sets out the main parameters and how their importance changes by application.

The core parameters

  • Total nitrogen. Pure urea is about 46.6% nitrogen; commercial grades are typically guaranteed at 46% minimum. It confirms purity and sets dosing calculations.
  • Biuret. Formed when urea is heated during evaporation and finishing. It matters most for DEF and for some chemical syntheses.
  • Moisture. Affects caking, flow and weighing accuracy.
  • Free ammonia. Residual ammonia affects odour, pH and some reactions.
  • Aldehydes or formaldehyde. Usually from anti-caking conditioners. Critical for DEF.
  • Insoluble matter. Determines filtration load and nozzle or catalyst fouling risk.
  • Trace metals and phosphate. Critical for DEF, relevant to colour in resins.
  • Particle form and size. Prilled or granular; affects dissolving rate, dust and flow.

Comparison by end use

ParameterUF / MUF resinsDEF / AUS 32 productionSNCR / SCR reagent
NitrogenHigh and consistent, for molar ratio accuracyHigh; purity confirmed by impurity limitsStandard 46% minimum
BiuretLimited, agreed with resin chemistLow enough for fluid to meet 0.3% maxModerate limits usually acceptable
Aldehydes / conditionerFormaldehyde-based conditioner often acceptable if declaredMust be essentially absent; uncoated ureaUsually acceptable if declared
Metals and phosphateLow iron helps colourVery tight; fluid limits of 0.2–0.5 mg/kg per elementNot usually critical
Insoluble matterLow, to avoid haze and filter loadingVery low; fluid limit 20 mg/kgLow, to protect nozzles
Moisture and flowImportant for automatic weighingImportant for clean handlingImportant if dissolving solids on site

DEF limits refer to the finished 32.5% solution under ISO 22241-1. Because the solution is about one-third urea, limits in the solid are roughly three times the fluid values before any safety margin.

Solid or solution

Many industrial users buy urea as solution rather than solid. Producers sell urea liquor at around 50% for DEF blending and industrial use, with their own biuret and aldehyde limits; for example, one producer's DEF-quality 50% liquor carries a biuret limit just under 0.5%. A 50% solution begins to crystallise below roughly 17–18 °C, so it needs heated storage. Solid urea is cheaper to transport over long distances and is the usual form for export trade, with dissolving done at the user's site.

Other industrial uses

Technical urea is also used in melamine production, in some adhesives and glues, in textile and paper finishing, as a formaldehyde scavenger, and in various chemical syntheses. For these uses the specification is usually agreed with the process owner, with nitrogen, biuret, moisture and conditioner the most commonly listed items.

Write the specification around the end use. One urea can be ideal for a resin plant and unusable for a DEF blender.

Testing and documents

Ask for a certificate of analysis per lot that covers every parameter in your specification, with the test methods named. For DEF use, align methods with ISO 22241-2. Request the SDS and, for high-value or critical shipments, independent inspection and sampling at loading. Retain samples from each lot.

Turning this into an enquiry

State the end use, preferred form (prilled or granular), each parameter with its limit, whether conditioners are allowed, packing, and required documents. Nuroil supplies technical-grade urea sourced from established producers, with a CoA on every delivery and certificate of origin, MSDS and third-party inspection on request, on FOB, CFR or CIF terms. Send details through our quote request page.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote