Diesel exhaust fluid, known in the international standard as AUS 32, is a solution of 32.5% high-purity urea in demineralised water. Trucks, buses, off-road machinery and some marine engines inject it into their selective catalytic reduction (SCR) systems to reduce nitrogen oxides. Many DEF / AUS 32 producers make it by dissolving solid urea, so the quality of that urea decides whether the finished fluid meets the standard. This article explains what a blending plant should look for.
The standard behind the product
AUS 32 quality is set by ISO 22241. Part 1 sets the quality requirements, part 2 gives test methods, and part 3 covers handling, transport and storage. The current edition of part 1 dates from 2019, and a revision is in progress, so producers should work to the edition their customers and regulators reference.
The limits are tight because impurities poison or foul the SCR catalyst and can block the dosing system. The table below shows key values commonly published from ISO 22241-1.
| Parameter | Limit in finished AUS 32 |
|---|---|
| Urea content | 31.8–33.2% (target 32.5%) |
| Biuret | 0.3% maximum |
| Aldehydes | 5 mg/kg maximum |
| Insoluble matter | 20 mg/kg maximum |
| Alkalinity as NH₃ | 0.2% maximum |
| Phosphate (PO₄) | 0.5 mg/kg maximum |
| Calcium, iron, magnesium, sodium, potassium, aluminium | 0.5 mg/kg maximum each |
| Copper, zinc, chromium, nickel | 0.2 mg/kg maximum each |
What this means for solid urea
Because the finished fluid is about one-third urea, any impurity in the solid is diluted roughly three times. Working backwards gives a rough feel for what the raw urea must achieve:
- Biuret in the solid must stay below roughly 0.9% for the fluid to meet 0.3%, and producers usually want a margin below that.
- Aldehydes must be almost absent. Ordinary fertilizer urea treated with a formaldehyde-based anti-caking agent can carry far more aldehyde than the fluid allows. DEF producers therefore specify uncoated, formaldehyde-free urea.
- Metals and phosphate must be at single-digit mg/kg levels in the solid. Contamination from dust, rust or reused bags can be enough to fail a batch.
- Insoluble matter must be very low, which rules out urea that has picked up dirt in handling.
Some producers prefer to buy concentrated urea solution made specifically for DEF, which avoids dissolving solids altogether. Others dissolve solid technical urea made and packed for this use. Either way, the specification should name ISO 22241 as the target for the finished product.
Water and equipment
Urea is only part of the picture. The water must be demineralised or deionised to a quality that keeps metals and phosphate within limits. Tanks, pumps, pipework and seals should be in materials compatible with AUS 32 as described in ISO 22241-3, typically stainless steel and suitable plastics. Copper, brass, zinc-coated steel, aluminium and ordinary carbon steel are generally avoided because they corrode and release ions into the fluid.
Blending practice
- Allow for cooling. Urea absorbs heat as it dissolves, so a fresh batch can become noticeably cold. Industry guidance notes temperatures dropping to around 4 °C in plant blending, which slows further dissolution.
- Check concentration. Refractive index and density are quick ways to confirm urea content within the 31.8–33.2% window before release.
- Filter and test. Filter before filling, and test each batch against ISO 22241-2 methods.
- Protect from contamination. Use dedicated, sealed containers. DEF should not be put into drums or totes previously used for other products.
Finished AUS 32 freezes at about −11 °C and thaws without separating. Storing it cool and out of sunlight preserves shelf life, since warm storage slowly breaks some urea down into ammonia.
For DEF, the urea must be uncoated and very clean. A conditioner that is harmless in a fertilizer can make a batch fail.
Buying urea for DEF production
State clearly that the urea is for DEF / AUS 32 production to ISO 22241, and specify uncoated, formaldehyde-free product with limits on biuret, aldehydes, metals, phosphate and insolubles. Ask for a certificate of analysis per lot, the SDS and packing that protects against contamination, such as lined bulk bags. Nuroil supplies technical-grade urea with a CoA on every delivery and can arrange third-party inspection. Contact us with your specification.


