Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read8 sections

Knowledge centre · Waterproofing & construction

Solvent-borne bitumen paint vs bitumen emulsion coatings

A comparison of solvent-borne black bitumen paint and water-based bitumen emulsion coatings for metal, concrete and buried surfaces.

Written by the Nuroil trade desk, Sharjah

NURPAINT protective bitumen paint
On this page · 8 sections
  1. 01How each one forms a film
  2. 02Relevant standards
  3. 03Side-by-side comparison
  4. 04Choosing for metal
  5. 05Choosing for concrete and buried surfaces
  6. 06Choosing for storage and logistics
  7. 07Service limits shared by both
  8. 08Specifying either type

Black protective bitumen coatings come in two main forms. Traditional bitumen paint is bitumen dissolved in a hydrocarbon solvent. Bitumen emulsion coatings carry bitumen as droplets dispersed in water. Both leave a black bitumen film, but they behave differently in the tin, on the wall and in service. This guide compares them so you can choose the right one for a given surface.

How each one forms a film

01

Solvent-borne bitumen paint

dries as the solvent evaporates, leaving bitumen behind. Because the bitumen is in solution, it wets clean, dry surfaces readily and dries predictably as long as there is airflow.
02

Bitumen emulsion coatings

dry as water evaporates or is absorbed, and the bitumen droplets coalesce into a film. The process depends on temperature, humidity and substrate absorbency, and the coating usually changes from brown to black as it cures.

Relevant standards

Standards bodies treat the two separately. BS 3416 covers bitumen-based solvent-borne coatings for cold application on iron, steel and other substrates. ASTM D1187 covers asphalt-base emulsions applied in a relatively thick film as protective coatings for metal, in two types: one quick-setting and suitable for continuous water exposure within a few days of drying, and one suitable for weather exposure once dry. ASTM D1227 covers emulsified asphalt for protective roof coatings.

Side-by-side comparison

FactorSolvent-borne bitumen paintBitumen emulsion coating
CarrierWhite spirit or similar hydrocarbonWater
Flammability in the tinFlammable; flash point around 40 °C in some productsNot flammable as a liquid
Odour and vapourNoticeable solvent vapourLow odour
Substrate moistureNeeds dry surfaceOften tolerates slight damp
Cold and humid weatherDries more reliablySlow drying; rain-sensitive until set
Frost in storageNot damaged by freezingRuined by freezing
Film build per coatThinCan be thicker in heavy-bodied grades
Clean-upSolventWater while wet
OverpaintingBleeds through solvent-borne paintsCheck data sheet; may still stain

Choosing for metal

For small steel items, fixings, gutters and buried steel, solvent-borne bitumen paint is familiar, easy to brush and dries quickly in normal conditions. Where a thicker, water-resistant film is wanted on metal, emulsion coatings to ASTM D1187 are an option, but they must be allowed to set fully before water exposure. In both cases, loose rust must be removed first, as neither type stops existing corrosion.

Choosing for concrete and buried surfaces

On foundations, footings and basement walls, both types can provide dampproofing where there is no hydrostatic pressure. Emulsions are often preferred where concrete is not fully dry or in enclosed spaces where solvent vapour is a concern. Solvent-borne paint suits dry surfaces and cooler weather when a quick-drying coat is needed before backfilling.

Choosing for storage and logistics

Solvent-borne products are classed as flammable liquids for storage and transport, which affects warehouse arrangements and shipping documents. Emulsions avoid that classification in most cases but need frost-free storage and transport, which matters on winter routes and in cold inland destinations.

Service limits shared by both

The carrier changes how the coating goes on, not what it is once dry. Both types leave a bitumen film, so both share the same service limits: they soften with heat, are attacked by mineral oils, fuels and paint solvents, and are not decorative finishes. Neither should be used in contact with drinking water unless the specific product is approved for it.

Choose solvent-borne paint for speed and reliable drying on dry surfaces. Choose emulsion where moisture, enclosed spaces or flammability are the main concerns.

Specifying either type

In an enquiry, give the substrate, exposure, site temperature range and destination climate, and say whether an overcoat is planned. Ask for the TDS, SDS and CoA, and the transport classification. Nuroil supplies bitumen paint and water-based bitumen primers; send details through the quote form.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote