Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read7 sections

Knowledge centre · Waterproofing & construction

Coverage rates for solvent-based bitumen primer and estimating quantities

Typical coverage of solvent-based bitumen primer, converting between m² per litre and litres per m², and estimating pails and drums for a roof or basement.

Written by the Nuroil trade desk, Sharjah

NURPRIME SB solvent-based bitumen primer
On this page · 7 sections
  1. 01Typical coverage figures
  2. 02Converting between units
  3. 03What changes real consumption
  4. 04Worked estimate
  5. 05Pails or drums
  6. 06Shelf life and ordering
  7. 07Your enquiry

Primer is usually a small line in a waterproofing budget, but running short on site stops the membrane crew. Ordering too much leaves pails that may pass their shelf life. This guide shows typical coverage figures for solvent-based bitumen primer and how to turn them into a reliable order.

Typical coverage figures

Manufacturers commonly publish coverage for one coat on a sound concrete surface:

  • several Gulf-region primers give 4 to 6 m² per litre per coat;
  • a North American mod-bit primer gives 4 to 7 m² per litre;
  • some European products quote consumption of about 0.2 to 0.3 litres per m² instead.

All of these stress that coverage depends on the porosity and texture of the surface, and several recommend a site trial to confirm the rate.

Converting between units

Data sheets use two conventions. Converting is simple:

Litres per m² = 1 ÷ coverage in m² per litre.
Coverage (m²/L)Consumption (L/m²)Litres per 1,000 m²20 L pails per 1,000 m²
30.3333317
40.2525013
50.2020010
60.171679
70.141438

Pail counts are rounded up. Some data sheets give primer weight per area instead; use the density on the sheet, typically about 0.85 to 0.95 kg per litre, to convert.

What changes real consumption

  • Porosity: open-textured blockwork and dry, weak concrete absorb more. Data sheets often recommend a second coat on highly porous surfaces, which can nearly double consumption.
  • Surface texture: broom-finished or rough slabs use more than power-floated ones.
  • Upstands and details: parapets, upstands, drains and pipe penetrations add area that is easy to leave out of a plan measurement.
  • Method: spraying is fast but produces overspray; brushing works primer into pores and can use more per square metre than rolling.
  • Re-priming: areas primed but not covered the same day may need another coat.
  • Waste: material left in pails and spills.

Worked estimate

A flat roof measures 1,200 m² in plan, with 160 m of parapet upstand primed to 300 mm high.

  1. Upstand area: 160 m × 0.3 m = 48 m². Total area is about 1,250 m².
  2. Planned rate: 5 m² per litre for a single coat on a power-floated slab, giving 250 L.
  3. Allow for some porous areas needing a second coat, say 10 percent of the area: about 25 L more.
  4. Add 10 percent for waste and losses: about 300 L in total.
  5. That is 15 pails of 20 L, or one 200-litre drum plus five pails.

The rates used are illustrative. Use the data sheet for the product you buy and adjust after a trial area.

Pails or drums

Primers are typically supplied in 20 L pails and 200 L drums; some brands offer smaller tins. Pails are easier to move on roofs and reduce the quantity of flammable liquid open at the work face. Drums suit large, steady consumption and lower packaging cost, but need decanting into smaller closed containers. Because the product is flammable, keep only a shift's worth at the work face whatever the pack size.

Shelf life and ordering

Shelf life is typically up to 12 months in sealed containers stored as recommended. Order close to the programme and avoid large surpluses. Solvent can evaporate from damaged or poorly closed containers, which thickens the primer and changes its coverage.

Your enquiry

Give the area, number of coats, substrate type and preferred pack size, and state any standard such as ASTM D41. Ask for the data sheet coverage figures, safety data sheet and batch certificate of analysis. Nuroil supplies solvent-based bitumen primers FOB UAE ports or CFR/CIF on request; send your quantities through request a quote.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote