Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read6 sections

Knowledge centre · Caustic soda & soda ash

Using soda ash to raise pH and alkalinity in pools and water treatment

How soda ash raises pH and alkalinity in pool and process water, how it differs from bicarbonate, and how to dose it safely without clouding the water.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of soda ash production
On this page · 6 sections
  1. 01What soda ash does to water
  2. 02Typical targets for pool water
  3. 03Dosing soda ash correctly
  4. 04Wider water treatment uses
  5. 05Handling safely
  6. 06Ordering soda ash for pools and water treatment

Soda ash (sodium carbonate) is one of the most common chemicals for correcting low pH in swimming pools, and it has a long history in drinking water and industrial water treatment too. It is cheap, easy to handle and effective. It is also strong enough that careless dosing causes problems, so it is worth understanding what it does.

What soda ash does to water

Soda ash is strongly alkaline. A 1% solution has a pH of around 11.3. When it dissolves, the carbonate ions take up hydrogen ions from the water, so the pH rises. Some of the carbonate stays in solution as carbonate and bicarbonate, which add to the water's total alkalinity, meaning its capacity to resist changes in pH.

In practice:

  • Soda ash raises pH strongly and raises total alkalinity as well.
  • Sodium bicarbonate mainly raises total alkalinity, with a much smaller effect on pH.

Pool operators usually use bicarbonate when alkalinity is low but pH is acceptable, and soda ash when pH is low. Because alkalinity buffers pH, many operators correct alkalinity first and then fine-tune pH.

Typical targets for pool water

Pool pH is commonly kept between 7.2 and 7.8. Total alkalinity is often held around 80–120 mg/L (ppm), and calcium hardness is usually kept within a range set for the pool's surface. Local health codes and the pool designer's guidance take precedence over these general figures, so check the rules that apply to your site.

pH drifts down for predictable reasons. Acidic stabilised chlorine products such as trichloroisocyanuric acid tablets lower pH and alkalinity over time, as does over-dosing of acid. Pools using these sanitisers typically need regular soda ash additions. Pools on sodium hypochlorite tend to drift upward instead and need acid more often than alkali.

Dosing soda ash correctly

  1. Test first. Measure pH, total alkalinity and calcium hardness with a reliable kit or meter.
  2. Calculate the dose from the pool volume and the product label or the dosing charts used by your operator. Aim for small corrections rather than one large one.
  3. Pre-dissolve. Add the soda ash to a bucket of water, never water onto the chemical, and stir until dissolved. It gives off some heat as it dissolves.
  4. Add with circulation running, spreading the solution near the return inlets or feeding it through a chemical feeder, away from bathers.
  5. Retest after circulation before adding more.

Adding too much at once, especially to water with high calcium hardness, can push the pH locally so high that calcium carbonate comes out of solution. The water turns cloudy and scale can form on surfaces and in heaters. If this happens, stop dosing, let the filters run and recheck the balance.

Wider water treatment uses

Outside pools, soda ash is used to:

  • raise pH and alkalinity in drinking water to reduce corrosion of pipes and fittings
  • remove non-carbonate hardness in lime-soda softening, where calcium is precipitated as calcium carbonate
  • neutralise acidic industrial effluents and process streams

Municipal and utility buyers often reference a purchasing standard such as AWWA B201, which sets minimum requirements for soda ash used in treating potable water, wastewater and reclaimed water. It covers composition, sampling, testing and packaging. Drinking water regulators may also require product certification for treatment chemicals, so confirm this before ordering.

Handling safely

Soda ash is not flammable, but its dust and solutions irritate the eyes and can irritate skin. Wear safety goggles and gloves, and use dust protection when tipping bags. Store it dry, in its labelled container, and apart from acids and chlorine products. Only trained staff should handle pool chemicals, and the product SDS should be kept near the storage and plant room. If soda ash gets into the eyes, flush with clean water for at least 15 minutes and get medical advice.

Soda ash is the right tool for low pH. Dissolve it first, dose in small steps and retest, especially in hard water.

Ordering soda ash for pools and water treatment

Tell your supplier whether you need light or dense grade, as this depends on your feeder. Give the minimum purity, any standard you buy against, the pack size your operators can handle and the delivery port. Ask for the certificate of analysis and the SDS. Nuroil supplies soda ash to pool and water treatment distributors with a CoA for every delivery.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote