Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read5 sections

Knowledge centre · Waterproofing & construction

SBS modified membrane specifications: a parameter-by-parameter guide

A reference to the properties on an SBS modified membrane data sheet, the test standard behind each one and what it means in service.

Written by the Nuroil trade desk, Sharjah

Rolls of BITUROLL-S SBS waterproofing membrane
On this page · 5 sections
  1. 01The standards framework
  2. 02Main parameters and test methods
  3. 03How to read the numbers together
  4. 04Fire performance
  5. 05Using this in an enquiry

A data sheet for an SBS modified bitumen membrane can list a dozen or more properties, each with its own test standard. This guide sets out the main parameters, the methods usually cited, and what each one tells a specifier or buyer. Exact limits vary with product type and must be taken from the manufacturer's data sheet and declaration of performance.

The standards framework

In Europe, reinforced bitumen sheets for roof waterproofing are covered by EN 13707, which defines the characteristics a manufacturer must declare and refers to individual test methods. Sheets for basement tanking and other uses fall under related product standards. In North America, SBS sheets are covered by ASTM material specifications according to reinforcement: D6164 for polyester, D6163 for glass fibre and D6162 for combined polyester and glass. These are material specifications only and do not address the suitability of a particular roof design.

Main parameters and test methods

ParameterTypical EN methodWhat it tells you
Length, width, straightnessEN 1848-1Roll yield and how well the sheet lays straight for even laps
Thickness and mass per unit areaEN 1849-1Amount of compound; drives durability and handling weight
WatertightnessEN 1928Resistance to water under pressure
Tensile strength and elongationEN 12311-1Load capacity and ability to stretch over moving joints; mainly set by reinforcement
Tear resistance (nail shank)EN 12310-1Resistance to tearing at mechanical fixings
Joint peel and shear strengthEN 12316-1, EN 12317-1Strength of lapped seams
Flexibility at low temperatureEN 1109Cold bending temperature; key indicator of SBS quality
Flow resistance at elevated temperatureEN 1110Temperature at which compound starts to slide on a vertical sample
Dimensional stabilityEN 1107-1Shrinkage or growth after heating; affects lap integrity
Resistance to impact and static loadEN 12691, EN 12730Resistance to puncture from dropped tools and point loads
Artificial ageingEN 1296 (heat), EN 1297 (UV)How much flexibility and flow resistance are retained over time
Granule adhesionEN 12039How well the cap surfacing stays in place

How to read the numbers together

01

Cold flexibility and flow resistance

define the compound's working window. SBS compounds typically show very good flexibility well below freezing, with flow resistance lower than that of APP compounds. Look at both values after ageing as well as new.
02

Tensile strength and elongation

depend largely on reinforcement. Polyester gives higher elongation and tear strength; glass gives dimensional stability but little stretch. A high tensile figure with very low elongation is characteristic of a glass carrier.
03

Thickness and mass

should be compared on the same basis. Granule-surfaced caps carry extra weight from the mineral, so a 4.5 kg/m² mineral cap may contain a similar amount of compound to a lighter sanded sheet. Ask for nominal thickness and tolerance, and measure on delivery if needed.
04

Declared values are usually minimums or limits with tolerances

The ASTM specifications state that their limits are minimum properties, not targets. A value stated as "≥" or "≤" should be read as the guaranteed limit, not the average.

Fire performance

Fire performance of a roof is a system property tested on the full build-up (membrane, insulation, deck), not on the sheet alone. Where local regulations require a fire classification, ask for the system test reference that matches your intended build-up.

Compare data sheets only when the same test method and condition (new or aged) are used for each parameter.

Using this in an enquiry

List the parameters that matter for your project, the test method you expect and any minimum values from your design specification. Ask for the product data sheet, declaration of performance where applicable, and the certificate of analysis for the batch supplied. Nuroil provides a CoA with every delivery and can arrange third-party inspection on request; send your list through our quote request form.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote