Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Waterproofing & construction

Joint reservoir size, shape factor and backer rod for bitumen sealant

Reference on sealant reservoir geometry for pavements: width-to-depth ratio, fill profiles, backer rod selection and estimating sealant quantities.

Written by the Nuroil trade desk, Sharjah

NURMASTIC rubberized bitumen sealant
On this page · 6 sections
  1. 01Shape factor
  2. 02Fill profiles
  3. 03Reservoir sizes for asphalt cracks
  4. 04Backer rod selection
  5. 05Estimating sealant quantity
  6. 06Ordering

A sealant can only stretch so far. How far a given bead must stretch depends on the width of the joint, how much the joint moves, and the depth of the sealant. Getting the reservoir geometry right lets a good product deliver its rated performance; getting it wrong can cause even a high-grade sealant to tear. This guide covers the main geometry rules for hot-poured bitumen sealants in concrete and asphalt pavements.

Shape factor

Shape factor is the ratio of sealant width to sealant depth in the reservoir. When a joint opens, a deep, narrow bead develops much higher strain at its surface and at the bond line than a shallow, wide one. That is why specifications control depth as well as width.

  • For hot-poured sealants, a width-to-depth ratio of about 1:1 is commonly recommended for concrete joints.
  • Silicone sealants, often used as an alternative on concrete, are typically placed at 1:1 to 2:1 and recessed below the surface.
  • Agency specifications define shape factor and require the backer material to establish it, so check the project documents for the exact figures.

Fill profiles

ProfileDescriptionTypical use
FlushSealant level with the pavement surfaceHot-poured sealant in concrete joints and routed asphalt cracks
RecessedSealant a few millimetres below the surfaceWhere traffic or snowploughs would pull out a flush bead; common for silicone
OverbandThin, narrow film over the crack edgesAsphalt crack sealing where the edges are irregular

Overbands should be kept thin and narrow. Some specifications reject sealant spread more than about 13 mm either side of the crack edge, and producer guidance limits the height of an overband above the surface to a millimetre or two. Wide or thick overbands increase tracking and pull-out in hot weather.

Reservoir sizes for asphalt cracks

For routed cracks in asphalt, published guidance from producers sets reservoir widths and depths according to climate, using wider, shallower reservoirs where pavements reach higher temperatures. Reservoir widths are typically kept below about 38 mm. One state specification sets a minimum routed reservoir of roughly 10 mm wide by 13 mm deep for narrow cracks. Follow the project specification or the sealant producer's table rather than a single rule.

Backer rod selection

In concrete joints, backer rod sets the depth of the sealant and stops it bonding to the bottom of the joint, so that the bead works only between the two walls. ASTM D5249 sets requirements for backer materials and notes that they must withstand the temperature of hot-applied sealants without excessive deformation. Practical points:

  • Use a heat-resistant rod with hot-poured sealant; ordinary foam rods may melt or shrink.
  • Choose a diameter somewhat larger than the joint width so the rod is held in compression and stays at the set depth.
  • Insert with a roller or tool set to a fixed depth, and avoid puncturing closed-cell rods, which can release gas into the hot sealant and cause bubbles.

Estimating sealant quantity

Sealant volume per metre equals the reservoir width times the sealant depth, plus any overband. Multiply by the total length of joints or cracks and by the sealant density from the data sheet to get mass, then add an allowance for melter residue, waste and uneven reservoirs. For example, a 12 mm by 12 mm bead holds 144 cm³ per metre, or 0.144 litres. Estimating from the actual reservoir size rather than nominal crack width avoids under-ordering.

Shape the reservoir first, then choose the sealant. Geometry and product work together.

Ordering

When requesting bitumen sealant, include the reservoir dimensions, total linear metres and fill profile so the supplier can confirm quantity and recommend packing. Ask for the product density, heating limits and the SDS. Backer rod and primers, where specified, can be sourced alongside other construction products.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote