Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read6 sections

Knowledge centre · Waterproofing & construction

HPMC in gypsum plasters compared with cement mortars

How HPMC behaves differently in gypsum-based plasters and cement-based mortars, and what that means for grade choice and dosage.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of a roof being waterproofed with bitumen membrane
On this page · 6 sections
  1. 01Why water retention matters to each binder
  2. 02Dosage differences
  3. 03Stickiness and workability
  4. 04pH and dissolution
  5. 05Effect on setting
  6. 06Specifying HPMC for each binder

Hydroxypropyl methylcellulose (HPMC) is used in both gypsum-based and cement-based dry-mix products, and in both it thickens the mix and holds water. But the two binders set by different chemistry, run at different pH and are applied in different ways, so a grade that works well in a tile adhesive is not automatically right for a gypsum machine plaster. This article explains the main differences.

Why water retention matters to each binder

Cement gains strength by hydrating over days and weeks. If an absorbent substrate or hot weather pulls water out of a thin mortar layer too early, hydration near the bond line is incomplete and adhesion suffers. HPMC slows that water loss. A laboratory study on cement mortar found that HPMC forms a colloidal film and bridges particles, raising the plastic viscosity of the mix and with it the water retention.

Gypsum plaster sets much faster, by crystallisation of calcium sulphate dihydrate, typically within an hour or so depending on retarders. Here water retention keeps the plaster workable for long enough to spread, level and finish, and ensures there is enough water for full crystallisation in a thin layer on a porous wall.

Dosage differences

Gypsum plasters tend to need comparatively high additions of cellulose ether to retain enough water. A patent on gypsum compositions notes addition rates of roughly 0.22 to 0.45% of total solids for ordinary gypsum, and another describes plaster and filler compositions with 0.1 to 1.0% cellulose ether by dry weight. In the cement mortar study, water retention rose steeply up to about 0.10% HPMC by cement mass and then levelled off. Exact figures depend on the formulation, the sand and the target performance, so each product needs its own trials.

Stickiness and workability

A high-viscosity HPMC improves water retention but can make a gypsum mortar tacky, so it drags on the trowel and is hard to finish. Machine-applied gypsum plasters often use grades chosen for a balance of water retention, pumpability and smooth finishing. Cement-based tile adhesives, by contrast, often use high-viscosity grades because high thickening helps resist slip of heavy tiles and extends open time.

pH and dissolution

Many construction-grade HPMCs are surface treated so that they disperse in water without lumping and then dissolve after a short delay. This delayed dissolution is typically triggered by the alkalinity of a cement mix. Gypsum systems are close to neutral, so a surface-treated grade may dissolve more slowly there. Formulators often specify untreated or differently treated grades for gypsum. Ask the supplier which treatment a grade has and which binder it is intended for.

Effect on setting

HPMC delays early cement hydration; the cement mortar study recorded slower early hydration as dosage increased. In gypsum, cellulose ethers are used alongside separate set retarders, and the combination must be balanced so that the plaster is workable but still sets on time.

AspectGypsum plasterCement mortar or tile adhesive
Main role of HPMCWorkability and water for crystallisationWater for hydration, open time, slip resistance
Typical environmentNear-neutral pHStrongly alkaline
Viscosity choiceBalanced for finish and pumping; very high grades can be tackyOften medium to high for adhesion and anti-slip
Surface treatmentCheck suitability; delayed-dissolution grades may dissolve slowlyDelayed-dissolution grades widely used
Interaction with settingUsed with separate retardersRetards early hydration

Specifying HPMC for each binder

In an enquiry, state the end product (gypsum hand plaster, gypsum machine plaster, cement render, tile adhesive, skim coat), the viscosity grade and measuring method you use, whether you need a surface-treated grade, and the quantity and packing. Ask for the technical data sheet, a certificate of analysis showing viscosity, moisture and ash, and the SDS. Nuroil supplies HPMC on request for construction chemical manufacturers; use the quote form to share your specification.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote