Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read8 sections

Knowledge centre · Waterproofing & construction

Bitumen sealant test results and what each one tells you

How to read a bitumen joint sealant certificate: cone penetration, resilience, softening point, flow, bond and heat stability results explained.

Written by the Nuroil trade desk, Sharjah

NURMASTIC rubberized bitumen sealant
On this page · 8 sections
  1. 01Cone penetration
  2. 02Resilience or elastic recovery
  3. 03Softening point
  4. 04Flow
  5. 05Bond and extension
  6. 06Heat stability and asphalt compatibility
  7. 07Reading the certificate
  8. 08Buying with confidence

A certificate of analysis for a hot-applied bitumen sealant lists a handful of laboratory results. Each one is a proxy for a field behaviour: how hard the sealant is, how well it springs back, whether it will flow in summer and whether it will stay bonded in winter. This guide explains the common tests in the ASTM D6690 and EN 14188-1 / EN 13880 frameworks so that buyers can read a certificate with confidence.

Cone penetration

A standard cone is allowed to sink into the conditioned sealant at 25 °C for a set time, and the depth is reported in tenths of a millimetre. Higher numbers mean a softer sealant. Specifications set a window rather than a single value: too hard and the sealant will not stretch with the joint in cold weather; too soft and it will flow or track in heat. In a published study of six European hot-applied sealants, one product fell outside its specified penetration range, showing that the check is worth making on every batch.

Resilience or elastic recovery

A ball penetrates the sealant and the amount it recovers after the load is removed is measured as a percentage. High resilience shows that the compound is elastic rather than just plastic, which usually indicates polymer or rubber modification. Elastic sealants resist stone intrusion because they push small particles back out, and they recover after joint movement. The same study recorded recovery values above 90% for all the products tested, consistent with heavy elastomeric modification.

Softening point

The ring-and-ball softening point is the temperature at which a disc of sealant sags under a steel ball. It is a quick indicator of high-temperature resistance. For hot climates, where pavement surfaces can become very hot in summer, a high softening point helps prevent the sealant from flowing out of the joint or sticking to tyres.

Flow

A sample is held on an inclined plate at an elevated temperature for several hours and the distance it slides is measured. Flow is a more direct test than softening point for whether the sealant will stay in place on a hot, sloping joint face.

Bond and extension

Sealant is poured between two blocks of concrete or asphalt, conditioned at a low temperature, then stretched by a set percentage and recompressed over several cycles. The specimen must show no cracking, separation or loss of bond. This is the test that most closely represents winter performance, and its temperature and extension define the difference between types and classes in the standards.

Heat stability and asphalt compatibility

Heat stability tests hold the sealant at elevated temperature for an extended period and measure the change in cone penetration, showing how much the compound stiffens with ageing. Compatibility tests place the sealant in contact with asphalt to check that oils do not migrate out and soften the surrounding mix or weaken adhesion.

TestWhat it simulatesWatch for
Cone penetrationGeneral consistencyResult inside the specified window
ResilienceRecovery after movement or stone pressureMinimum percentage met
Softening pointResistance to summer heatAdequate margin for local pavement temperatures
FlowStaying in the joint when hotFlow within limit
Bond / extensionWinter joint openingNo cracking or separation at specified temperature and extension
Heat stabilityAgeing and hardeningLimited change in penetration

Reading the certificate

  • Check that every property required by the specified type or class appears, with the test method and limit alongside the result.
  • Confirm that the batch number on the certificate matches the packaging.
  • Note that bond tests take longer than routine checks; some producers report them from periodic type testing rather than every batch. Ask how often each test is run.
  • Remember that laboratory results assume correct heating. A sealant overheated in the melter can lose the properties shown on its certificate.

Buying with confidence

Ask for the full certificate of analysis with test methods, the technical data sheet and the SDS before shipment. For large projects consider independent sampling and testing at loading. Nuroil provides a CoA with every delivery of bitumen sealant and can arrange third-party inspection on request.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote