Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Waterproofing & construction

Bitumen joint sealant standards: ASTM D6690 and EN 14188 explained

A reference to the main specifications for bitumen joint and crack sealants: ASTM D6690 types, EN 14188-1 and EN 14188-2 classes, and how to choose.

Written by the Nuroil trade desk, Sharjah

NURMASTIC rubberized bitumen sealant
On this page · 6 sections
  1. 01ASTM D6690
  2. 02EN 14188-1: hot-applied sealants
  3. 03EN 14188-2: cold-applied sealants
  4. 04Other references you may see
  5. 05How to choose
  6. 06Writing the enquiry

Bitumen joint and crack sealants are bought against a published specification so that buyer, supplier and site engineer agree on what the product must do. Two families of standards dominate international tenders: ASTM D6690 in the Americas and many other markets, and the EN 14188 series in Europe and countries that follow European practice. This guide explains what each covers.

ASTM D6690

ASTM D6690 is the standard specification for hot-applied joint and crack sealants for concrete and asphalt pavements. It replaced a group of older ASTM and US federal specifications and divides sealants into four types, mainly by the climate they are meant for.

TypeIntended conditionsDistinguishing feature
Type IModerate climatesLeast demanding low-temperature bond test
Type IIMost climatesBond test at a lower temperature than Type I
Type IIIMost climatesAs Type II plus additional tests carried over from a former federal specification
Type IVVery cold climatesLow-temperature bond test at much higher extension

The standard leaves it to the user agency to decide which type suits local conditions. It also states that it does not cover sealants for areas exposed to jet fuel or other fuel spillage, such as aprons and fuelling areas, which need fuel-resistant products. Test temperatures and limits have changed between editions, so always quote the edition in your specification.

EN 14188-1: hot-applied sealants

EN 14188-1 covers hot-applied normal and fuel-resistant joint sealants for roads, airfields and other concrete pavements, and also normal sealants used in bituminous surfacing and at junctions between asphalt and concrete. Normal sealants are divided into classes; N1 is a high-extension, elastic class and N2 a lower-extension class. Fuel-resistant classes are specified separately for areas exposed to fuel. Properties are tested using the EN 13880 series of methods, which cover:

  • cone penetration and resilience at 25 °C (consistency and elastic recovery);
  • heat stability, comparing penetration after prolonged heating;
  • flow resistance on an inclined surface at elevated temperature;
  • compatibility with asphalt, checking for oily exudation and loss of adhesion;
  • bond and extension, including cyclic movement tests on prepared joints.

Published product data for N1 sealants typically also report a ring-and-ball softening point.

EN 14188-2: cold-applied sealants

EN 14188-2 specifies cold-applied normal and fuel-resistant joint sealants for concrete pavements in roads, parking decks, bridge decks, airfields and other trafficked areas. Cold-applied sealants under this standard include many non-bitumen chemistries such as polysulphides, polyurethanes and silicones, as well as bituminous products. Earlier editions excluded petrol stations, aircraft fuelling stations and the chemical industry; later revisions widened the scope, so confirm which edition a tender refers to.

Other references you may see

  • ASTM D5249 covers backer material for use with cold- and hot-applied joint sealants.
  • ASTM D5893 covers cold-applied silicone sealants for concrete pavements, often specified as an alternative to hot-poured bitumen sealant on concrete joints.
  • National road authority specifications frequently adopt one of these standards with local additions, such as tighter softening point limits for hot climates.
Name the standard, the edition and the type or class. A sealant described only as "hot-pour" is not a specification.

How to choose

Start from the pavement and climate. Asphalt crack sealing in a moderate climate may be well served by a lower ASTM type, while concrete joints on a highway with large seasonal temperature swings need a higher-extension product. In hot regions, also check that the softening point and flow resistance are adequate to prevent tracking. Fuelling areas need a fuel-resistant class whatever the climate.

Writing the enquiry

State the standard, edition and type or class, the pavement type and the quantity. Ask for a certificate of analysis for the batch showing the specified test results, the technical data sheet with heating limits and the SDS. Where a project requires independent verification, request third-party inspection or testing. Nuroil supplies bitumen sealant with a CoA on every delivery and can arrange inspection on request; use the quote form to share your specification.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote