Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read5 sections

Knowledge centre · Caustic soda & soda ash

How soda ash is produced: synthetic and natural routes

A technical overview of the ammonia-soda (Solvay) process and natural soda ash refined from trona, and what the production route means for buyers.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of soda ash production
On this page · 5 sections
  1. 01The synthetic route: the ammonia-soda process
  2. 02The natural route: trona and brines
  3. 03The two routes side by side
  4. 04Does the route matter to the user?
  5. 05Points to cover when sourcing

Soda ash reaches the market by two broad routes. It is either made chemically from salt and limestone, or refined from natural sodium carbonate minerals and brines. Both routes produce anhydrous sodium carbonate of better than 99% purity, and both are used throughout the world. This guide outlines how each works and what, if anything, the route means for the buyer.

The synthetic route: the ammonia-soda process

Most synthetic soda ash is made by the ammonia-soda process, refined by Ernest Solvay in the 1860s. Its raw materials are brine (sodium chloride solution) and limestone, with ammonia circulating as a reagent. The main steps are:

  1. Lime kiln. Limestone is burned at around 950–1,100 °C to give quicklime and carbon dioxide.
  2. Ammoniation and carbonation. Purified brine absorbs ammonia, then carbon dioxide is bubbled through it. Sodium bicarbonate, which is only slightly soluble under these conditions, crystallises out, leaving ammonium chloride in solution.
  3. Calcination. The filtered bicarbonate is heated to about 160–230 °C. It decomposes to sodium carbonate, and the water and carbon dioxide released are recycled.
  4. Ammonia recovery. Lime from the kiln reacts with the ammonium chloride liquor to release ammonia for reuse. Calcium chloride is left as the main by-product.

Overall, salt and limestone become sodium carbonate and calcium chloride. The calcined product is light soda ash. To make dense ash, producers typically hydrate light ash to sodium carbonate monohydrate and dry it again, which gives larger, heavier grains.

A variant developed in the 1930s, often called the Hou process, links the plant to ammonia production. It recovers ammonium chloride as a saleable product, usually for fertilizer, instead of producing calcium chloride.

The natural route: trona and brines

Natural soda ash is refined from trona, a mineral of sodium carbonate, sodium bicarbonate and water, or from sodium-carbonate-rich lake brines. Commercially workable trona deposits occur in only a few places worldwide. The ore is mined underground by conventional methods or recovered by solution mining, where water is injected to dissolve the trona and the brine is pumped to the surface.

The main refining method is the monohydrate process:

  1. Crushed trona is calcined at around 150–300 °C. This drives off water and carbon dioxide and leaves crude soda ash containing insoluble shale.
  2. The crude ash is dissolved in hot water. Insolubles are settled and filtered out, and organic traces may be removed with activated carbon.
  3. Sodium carbonate monohydrate is crystallised in evaporative crystallisers.
  4. The crystals are dewatered and dried at about 150 °C to anhydrous dense soda ash, then screened.

An older sesquicarbonate process crystallises sodium sesquicarbonate first and calcines it. It yields light to intermediate grades. Brine-based plants carbonate the brine to precipitate bicarbonate, then calcine and densify it.

The two routes side by side

AspectAmmonia-soda (synthetic)Natural (trona or brine)
Main raw materialsSalt brine, limestone, recycled ammoniaTrona ore or sodium carbonate brines
Direct productLight ash, densified as neededMainly dense ash (monohydrate route)
Main by-product or residueCalcium chloride solutionInsoluble ore residues (tailings)
Energy and CO2Generally higherGenerally lower
Typical trace impuritiesChloride from the brine feedSulphate and trace organics from the ore

Government mineral surveys note that synthetic production normally uses more energy and releases more carbon dioxide than natural production. Natural producers therefore tend to have lower production costs where large deposits exist.

Does the route matter to the user?

For most applications, no. Both routes routinely meet the same commercial and water-treatment standards, and the product is chemically identical. The differences show up in trace impurities and physical form. Synthetic ash may carry slightly more chloride. Natural dense ash comes straight from crystallisation, while synthetic dense ash is densified light ash, and the two can differ in grain shape and particle size distribution.

It is therefore better to buy against measurable parameters than against a production route. Define the purity, chloride, iron, bulk density and particle size your process needs, and judge every source by its analysis.

Points to cover when sourcing

State the grade, the specification limits that matter, packing and destination. Ask for the certificate of analysis, and the certificate of origin if your customs or customers need it. Nuroil sources soda ash from established producers and supplies both dense and light grades, with CoA, SDS and inspection documents available on request.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote