Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Sulphur

Handling prilled sulphur: reducing breakage and dust

Where prilled sulphur breaks down into dust along the supply chain, and practical measures for conveyors, stockpiles, loading and receiving.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of prilled sulphur
On this page · 6 sections
  1. 01Why prills break
  2. 02Conveying and transfer points
  3. 03Stockpiles
  4. 04Ship loading and discharge
  5. 05Protecting people
  6. 06What to agree with your supplier

Prilled sulphur is chosen partly because it creates less dust than crushed or lump sulphur. That advantage only holds if the prills stay whole. Every drop, transfer and pass of a loader can break some of them, and the fines produced are the source of most of the fire, explosion, health and housekeeping problems with formed sulphur. This guide follows the prill through the supply chain and lists where breakage happens and how to reduce it.

Why prills break

  • Impact. Free fall from conveyors, grabs and into holds is the biggest single cause. The higher the drop, the more breakage.
  • Abrasion. Prills rubbing on each other in chutes, screws and piles wear down slowly.
  • Crushing. Vehicles driving on stockpiles and loader buckets pushing into piles crush particles.
  • Ageing. Formed sulphur slowly converts to its stable crystal form after production and can become more friable with time.
  • Shape and structure. Irregular, porous or hollow prills, more common with some water prilling processes, break more easily than dense, round ones.

Conveying and transfer points

  • Keep drop heights short and use lowering chutes, cascade or spiral chutes where long drops cannot be avoided.
  • Run belts at moderate speeds and avoid sharp changes of direction.
  • Enclose transfer points and fit dust extraction designed for combustible dust.
  • Bond and earth conveyors and chutes; moving sulphur generates static, which can ignite dust.
  • Use belts, idlers and lighting rated for dusty atmospheres where required.

Stockpiles

  • Build piles with a stacker or radial conveyor that lowers as the pile grows, rather than dropping from height.
  • Reclaim from the face with as little driving on the pile as possible.
  • Store on a hard, drained pad; run-off from sulphur is acidic and should be collected.
  • Rotate stock so the oldest material, which may be more friable, is used first.
  • Keep hot work and other ignition sources away and maintain fire-fighting water.

Ship loading and discharge

Formed sulphur that meets the shape requirements is carried as an IMSBC Group C cargo rather than under the stricter rules for crushed and lump sulphur, but dust control still matters. Trimming spouts that reduce free fall, loading at moderate rates and avoiding loading in strong winds all help. Grab discharge should minimise drop height into hoppers. Ship owners also expect clean, dry, often lime-washed holds, since wet sulphur corrodes steel.

Bagged prills. Prilled sulphur in jumbo bags or smaller bags suffers less breakage in transit, but the bags must be filled and emptied carefully. Bag discharge stations with dust hoods, and filling at controlled rates, keep fines down. Bags should be stored dry and away from heat.

StageMain cause of finesKey control
ConveyingDrops at transfer pointsShort drops, enclosed transfers
StockpilingFree fall and vehicle trafficLowering stacker, limited traffic
Ship loadingFree fall into holdTrimming spout, moderate rates
Long storageAgeingFirst in, first out

Protecting people

Sulphur dust irritates eyes, skin and airways. Workers in dusty areas normally wear dust masks or respirators, goggles and covering clothing. Burning sulphur produces sulphur dioxide; fire plans should include breathing apparatus and water fog or spray rather than solid jets that raise dust. Follow the product SDS and recognised guidance such as NFPA 655.

Every metre of free fall you remove from the handling chain saves fines, dust and risk later.

What to agree with your supplier

Ask for size distribution and fines at loading, the production date or age of the stock, and the packing type. Nuroil can supply prilled sulphur in bulk or bags, with a CoA on every delivery and inspection on request; request a quote to discuss handling at your port.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote