Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Sulphur

Melting granular sulphur for burners and acid plants

How plants melt granular sulphur for burners: pit temperatures, steam tracing, what impurities leave behind and the main safety points with molten sulphur.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of granular sulphur
On this page · 5 sections
  1. 01The melting window
  2. 02How granules behave in the melter
  3. 03What impurities leave behind
  4. 04Safety with molten sulphur
  5. 05Specifying sulphur for melting

Many users of solid sulphur, from sulphuric acid plants to sugar mills running sulphitation and makers of sulphur chemicals, do not use it solid at all. They melt it and burn the liquid to make sulphur dioxide. Granular sulphur is a convenient feed for this because it is free-flowing and relatively dust-free. Getting from granules to a clean, steady liquid feed still depends on good melter practice.

The melting window

Sulphur melts at around 115 to 120 °C. Above that, the liquid is thin and easy to pump, but it has an unusual property: if heated much beyond about 160 °C its viscosity rises sharply as the molecules join into long chains. Plant experience over many decades has settled on keeping molten sulphur at roughly 135 to 140 °C, where it is at its least viscous and pumps easily into the burner.

That temperature is normally held by low-pressure steam in coils inside the melting pit or tank. Pipework between the pit and the burner must be steam-jacketed or traced, because sulphur that cools in a line solidifies and blocks it.

How granules behave in the melter

  • Feeding. Granules flow well from hoppers and conveyors, so the melter can be fed steadily, which helps keep the pit temperature stable.
  • Melting rate. Granules of a few millimetres melt quickly once immersed. Adding large quantities at once can chill the pit and cause a solid crust, so match feed rate to steam capacity.
  • Fines. Broken granules and dust can float or stick to surfaces before melting and add to the dust hazard at the tipping point.
  • Moisture. Surface water boils off in the pit and can cause foaming and spitting. Drier sulphur melts more smoothly.

What impurities leave behind

Pure sulphur burns completely to sulphur dioxide. Impurities do not. Ash, made up of mineral matter, settles as sludge in pits and filters. Carbonaceous matter, often reported as carbon or organic content, can form dark deposits and add to the load on filters. Moisture combined with sulphur can lead to acidity that attacks carbon steel.

Impurity on the CoAEffect in a melting and burning system
AshSludge in pits; more frequent filter cleaning
Carbon / organic matterDark sulphur, deposits, extra filter load
MoistureFoaming and spitting on melting; extra steam use
AcidityCorrosion of carbon steel tanks and lines

Most melting systems include filtration of the liquid sulphur, either in pressure leaf filters or by settling, before it reaches the burner. The cleaner the sulphur, the longer between filter cleans.

Safety with molten sulphur

Molten sulphur brings hazards that solid granules do not:

  • Burns. Contact with the liquid causes severe thermal burns. Heat-resistant gloves, face shields and suitable clothing are standard.
  • Hydrogen sulphide. Trace H₂S dissolved in sulphur can collect in the headspace of pits, tanks and tankers to toxic or flammable levels. Ventilate before entry and use gas monitoring.
  • Fire. Burning sulphur gives off sulphur dioxide, which is toxic and suffocating. Some SDSs warn that water or foam on molten sulphur can cause frothing and boil-over, so follow the firefighting section of the SDS for your plant.
Hold the melt at about 135 to 140 °C, keep every line traced, and remember that the hazards change once the granules become liquid.

Specifying sulphur for melting

When you order granular sulphur for a melter, specify purity on a dry basis plus maximum ash, carbon, moisture and acidity. Ask for the CoA to report each one. Nuroil supplies granular sulphur from established refinery and gas-processing producers with a CoA on every delivery, and third-party inspection on request. Send your requirements through the quote request form.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote