Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Urea & fertilizers

Feed-grade urea quality parameters and what each one means

A reference to the parameters on a feed-grade urea certificate: nitrogen, crude protein equivalent, biuret, moisture, particle size and conditioners.

Written by the Nuroil trade desk, Sharjah

Illustration of Nuroil feed grade urea with cattle feeding
On this page · 6 sections
  1. 01Nitrogen and crude protein equivalent
  2. 02Specification table
  3. 03Biuret
  4. 04Moisture, particle size and flow
  5. 05Conditioners and regulatory status
  6. 06Writing the purchase specification

A certificate of analysis for feed-grade urea is short, but each line has a practical meaning for the nutritionist and the feed mill. This guide explains the usual parameters, typical limits seen on producers' sales specifications, and how to use them when writing a purchase specification. Exact limits differ by producer and by market, so always check the specification and local feed regulations that apply to you.

Nitrogen and crude protein equivalent

Pure urea contains about 46.6% nitrogen. Commercial feed grade is typically guaranteed at a minimum of 46.0% nitrogen. Nutritionists usually think in protein terms, so labels also give a crude protein equivalent, calculated as nitrogen multiplied by 6.25. A 46.0% nitrogen product therefore equates to 287.5% crude protein. That figure is a paper conversion only: urea supplies no amino acids, and its value depends on rumen microbes turning the nitrogen into microbial protein.

Some feed regulations set a minimum nitrogen for products sold simply as urea. One example is a US state rule that requires at least 45% nitrogen (281.25% crude protein equivalent) and requires products between 41% and 45% to be named as urea with conditioner. Coated or slow-release urea products have lower nitrogen for the same reason.

Specification table

ParameterTypical limit on feed-grade specificationsWhy it matters
Total nitrogen46.0% minimumSets the NPN dose; ration formulas assume it
Crude protein equivalentAbout 287.5% (N × 6.25)Used in ration software; follows directly from nitrogen
BiuretAbout 1.0–1.2% maximumBy-product of manufacture; limited on specifications
MoistureAbout 0.3% maximumHigher moisture means caking and poor mixing
Particle sizeFine micro-granules, often stated as a size guide numberSmaller, uniform particles disperse better in mash feeds
Conditioner or coatingDeclared by the producerMust be acceptable for feed in your market

Biuret

Biuret forms when urea is heated during manufacture, mainly in the evaporation and finishing stages. Ruminants can adapt to use some biuret as a nitrogen source, but it is not equivalent to urea and specifications cap it. A producer's typical value may be around 1% against a limit of 1.0–1.2%. Consistently low biuret also indicates good process control.

Moisture, particle size and flow

Urea is hygroscopic. Moisture pick-up leads to caking in bags and silos and to lumps that will not break down in a mixer. Feed grades are therefore supplied dry, with typical moisture well under the 0.3% limit, and as small micro-granules rather than the larger granules used for fertilizer spreading. Producers' sheets may also give bulk density (around 720 kg per cubic metre for one micro-granular grade) and angle of repose, which help when sizing bins and feeders.

Producers recommend storing feed urea at stable temperatures, roughly 10–30 °C, and at relative humidity below about 70%, keeping stack heights low and avoiding loading in rain.

Conditioners and regulatory status

Fertilizer urea is often treated with formaldehyde-based anti-caking agents. Feed grades are produced and handled under feed safety controls, and any conditioner must be one permitted for feed. In the European Union, urea is an authorised nutritional feed additive for ruminants with a functional rumen under identification number 3d1, and producers' directions follow that authorisation, including a guideline that no more than 30% of total ration nitrogen should come from urea nitrogen. Other markets have their own registrations and labelling rules.

Nitrogen sets the dose; moisture and particle size decide whether that dose is spread evenly.

Writing the purchase specification

A clear enquiry for feed-grade urea should state the intended use (ruminant feed), the market and feed regulation it must satisfy, minimum nitrogen, maximum biuret and moisture, particle size range, and whether a specific conditioner is required or excluded. Ask for a certificate of analysis per lot, the SDS, and the producer's feed safety or registration documentation. Nuroil supplies feed-grade urea with a CoA on every delivery, with certificate of origin and third-party inspection available on request. Send your specification via our quote request form.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the knowledge centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote