Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Waterproofing & construction

How to estimate cold asphalt quantities for patching

A simple method to work out how many kilograms or bags of cold asphalt a repair needs, with worked examples and allowances for compaction and waste.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of a cold-applied roadway repair
On this page · 6 sections
  1. 01The basic calculation
  2. 02Worked examples
  3. 03Choosing the allowance
  4. 04From individual holes to an annual order
  5. 05Common estimating mistakes
  6. 06Turning the estimate into an enquiry

Ordering too little cold asphalt sends crews back to the depot; ordering too much ties up stock that has a shelf life. A quick, consistent way of estimating quantities helps both site crews and buyers. The method below works for single potholes, a list of defects from a road survey or a small trench.

The basic calculation

The amount of cold asphalt needed is the compacted volume of the repair multiplied by the compacted density of the mix:

  1. Measure the repair. Length and width of the area after trimming to sound edges, and the depth to firm material.
  2. Work out the volume. Length × width × depth, in metres, gives cubic metres.
  3. Convert to weight. Multiply the volume by the compacted density from the product data sheet, in kilograms per cubic metre.
  4. Add allowances. Add for overfill, compaction and handling losses.
  5. Convert to packs. Divide by the pack weight and round up.

Compacted density varies with aggregate and binder, so always use the figure on the supplier's data sheet. Dense asphalt mixes are commonly in the region of 2,000 to 2,400 kg per cubic metre once compacted; for the examples below we use 2,200 kg per cubic metre purely to illustrate the method.

Worked examples

RepairSize (L × W × D)VolumeWeight at 2,200 kg/m³With 10% allowance25 kg bags
Small pothole0.4 × 0.3 × 0.04 m0.0048 m³about 10.6 kgabout 11.6 kg1
Medium pothole0.8 × 0.6 × 0.05 m0.024 m³about 52.8 kgabout 58.1 kg3
Trench surface5.0 × 0.5 × 0.05 m0.125 m³about 275 kgabout 303 kg13

A useful rule of thumb follows from the same arithmetic: at that illustrative density, one 25 kg bag fills roughly 0.45 square metres at 25 mm compacted depth, or about 0.23 square metres at 50 mm. Check this against the coverage figure your supplier publishes.

Choosing the allowance

An allowance of around 10 per cent is a sensible starting point, but adjust it for the work:

  • Irregular holes: potholes are rarely neat rectangles and often deeper in the middle. Measure the average depth, or add more allowance.
  • Overfill: patches are deliberately left slightly proud so traffic compacts them flush.
  • Loose to compacted: loose mix takes up more volume than compacted mix, so judge by weight rather than by how full the hole looks.
  • Waste: spillage, part bags left over and material that stiffens in opened packs.

From individual holes to an annual order

For programme planning, many road owners record the number and approximate size of defects found in inspections and use past consumption per kilometre of road or per season. Combine these records with the calculation above to set a seasonal order, and remember that pothole numbers usually rise after wet or freezing periods. Because cold asphalt has a shelf life, it is often better to order in stages through the season than to buy a full year's supply at once.

Common estimating mistakes

  • Measuring the visible hole rather than the area after trimming back to sound edges, which is usually larger.
  • Using the depth at the edge instead of the average depth across the hole.
  • Forgetting that deep holes are filled in several compacted layers and need the full volume, not just a surface skim.
  • Estimating by loose volume, which overstates how far a bag will go.
Measure, multiply by the data sheet density, add an allowance and round up to whole packs. Keep a record of actual use to refine the next order.

Turning the estimate into an enquiry

Give your supplier the total weight, pack size, delivery schedule, intended use and climate. Ask for the compacted density or coverage per pack, shelf life and SDS so your next estimate can use the right figures. Nuroil supplies ready-to-use cold asphalt; send your quantities through request a quote.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote