Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read7 sections

Knowledge centre · Caustic soda & soda ash

Dissolving dense soda ash: solubility, temperature and lumps

Soda ash solubility peaks near 35 °C and hydrates can set into hard lumps in cold water. How to make dense soda ash solutions and slurries reliably.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of dense soda ash with a glass furnace
On this page · 7 sections
  1. 01Solubility rises to a peak, then falls
  2. 02Why hydrates cause lumps
  3. 03Making a solution reliably
  4. 04Slurry storage for large users
  5. 05Typical uses of soda ash solutions
  6. 06Safety
  7. 07Buying for solution make-up

Dense soda ash is easy to store and convey, but it can be awkward to dissolve. Operators who tip it into cold water often find hard lumps on the tank floor or a crust that blocks the outlet. The reason lies in how sodium carbonate behaves with water at different temperatures.

Solubility rises to a peak, then falls

Sodium carbonate is unusual. Its solubility climbs steeply with temperature up to about 35 °C, where a saturated solution holds roughly 33% Na₂CO₃ by weight, then falls slightly as the water gets hotter. Reference data show about 7 g per 100 ml of water near 0 °C, about 16 g at 15 °C, and close to 49 g around 35 °C, easing to about 44 g near 100 °C.

Why hydrates cause lumps

Soda ash forms three hydrates. Below about 32 °C the stable solid in contact with solution is the decahydrate (Na₂CO₃·10H₂O); between about 32 and 35.4 °C it is the heptahydrate; above 35.4 °C it is the monohydrate. When anhydrous granules land in cool water, the surface starts to hydrate before the core dissolves. Wet granules lying together can knit into a hard mass of hydrate crystals that dissolves only slowly. In storage this is why damp soda ash cakes; in a dissolving tank, it is why lumps form on the floor.

Warm water, steady agitation and gradual feeding prevent most dissolving problems with dense soda ash.

Making a solution reliably

  1. Start with water in the tank and the agitator running, never with a heap of dry ash.
  2. Use warm water where possible. Working near 35 °C gives the highest solubility and avoids the decahydrate region.
  3. Feed gradually through a wetting cone, eductor or screw feeder so granules disperse rather than pile up.
  4. Target a concentration below saturation at the lowest temperature the solution will see. A strong solution made warm can crystallise in a cold dosing line overnight.
  5. Allow time. Dense granules dissolve more slowly than light or medium-dense grades because of their larger, compact particles.
  6. Filter or settle the solution if insolubles matter for your process.

Slurry storage for large users

Large users sometimes store soda ash as a slurry rather than dry. When enough ash is mixed into water above about 35 °C, part of it dissolves to saturate the liquid and the rest converts to monohydrate crystals that settle as a fluid, non-setting bed. Saturated solution is drawn from the top for use, and more dry ash is added to the tank as needed. Patent literature on this method notes that a slurry tank can hold up to about twice as much soda ash as the same volume of dry product. The system relies on keeping the tank warm enough to stay in the monohydrate region.

Typical uses of soda ash solutions

  • pH and alkalinity adjustment in water treatment.
  • Lime–soda softening, where carbonate precipitates calcium hardness.
  • Neutralising acidic process streams.
  • Feeding scrubbers that absorb sulphur dioxide from flue gas.

In each case, size the make-up tank so the solution has time to dissolve fully before it is drawn off, and keep dosing lines short or insulated if the solution is close to saturation.

Safety

Soda ash solutions are alkaline, with a 1% solution at about pH 11.4, and can irritate skin and seriously injure eyes. Wear goggles and gloves when dissolving, control dust at the feed point, and check the SDS for the product you use.

Buying for solution make-up

If you dissolve on site, tell your supplier so they can match the grade to your equipment; dense ash suits bulk handling but dissolves more slowly than lighter grades. Specify Na₂CO₃ content, insolubles and iron, and ask for a certificate of analysis per lot. Nuroil supplies dense soda ash in bags and big bags; ask through contact us.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote