Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read5 sections

Knowledge centre · Caustic soda & soda ash

Dense soda ash screen analysis and bulk density explained

How to read the screen analysis and bulk density on a dense soda ash data sheet, with typical limits and why each one matters to the user.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of dense soda ash with a glass furnace
On this page · 6 sections
  1. 01Bulk density
  2. 02Why bulk density matters
  3. 03Screen analysis
  4. 04How dense ash gets its size
  5. 05Testing on receipt
  6. 06What to specify

Two soda ash cargoes can both test at 99.5% sodium carbonate and still behave very differently in a plant. The difference lies in physical properties: particle size distribution and bulk density. For dense soda ash these are part of the specification, and they matter most to glass, silicate and detergent producers and to anyone with silos and pneumatic conveying. This guide explains how to read them.

Bulk density

Bulk density is the mass of loose product that fills a given volume, including the air between granules. It is quoted in kg/m³, g/cm³, grams per litre (GPL) or lb/ft³. Typical published ranges are:

Gradekg/m³ (approx.)lb/ft³ (approx.)
Dense soda ash1,000–1,10062–69
Fine or intermediate grades750–91047–57
Light soda ash700–86044–54

The absolute density of the sodium carbonate crystal itself is about 2.53 g/cm³; the bulk figure is lower because of the voids between particles.

Why bulk density matters

  • Storage volume: 1,000 t of dense ash at about 1.05 t/m³ needs roughly 950 m³ of silo space; the same tonnage of light ash needs considerably more.
  • Volumetric feeders: screw and rotary feeders deliver a volume. A change in bulk density changes the mass fed unless the feeder is recalibrated.
  • Batch mixing: in glass and silicate batches, soda ash with a bulk density close to sand's stays mixed better.
  • Freight: denser product loads more tonnes into a container or bag of a given size.

Screen analysis

Screen (sieve) analysis shows how the granules are distributed by size. A weighed sample is shaken through a stack of sieves and the material on each is weighed. Data sheets usually report cumulative percentages: the share retained on or above a given sieve, or the share passing through it.

A typical dense ash specification from a major producer reads:

SieveApertureLimitWhat it controls
US 30600 µmRetained: 4% maxOversize granules and lumps
US 100150 µmCumulative retained: 85% minMost of the product is coarser than 150 µm
US 20075 µmPassing: 2% maxFines and dust

By contrast, a finer grade may specify that 50–95% is retained on 45 µm and only up to 20% on 150 µm. The two grades are not interchangeable.

Fines create dust and carry-over; oversize creates slow melting and dissolving. A good dense ash has little of either.

How dense ash gets its size

Dense soda ash is made from light ash, either by converting it to a coarser crystal form and recalcining it, or, as some producers describe, by mechanically compacting light ash and then screening and classifying it into uniform granules. Either way, the producer controls particle size by screening, which is why a consistent screen analysis is a fair test of process control.

Testing on receipt

  • Take a composite sample from several bags or points in the bulk load; dense and fine particles can separate during handling.
  • Measure loose bulk density by filling a container of known volume without tapping.
  • Run screen analysis using the same sieve sizes as the specification.
  • Note caked lumps separately; they indicate moisture exposure rather than a size problem.

Small differences between your result and the certificate are normal, because sieving technique, shaking time and sample handling all affect the figures. Look for trends across lots rather than single readings, and agree the test method with the supplier so both sides measure the same way.

What to specify

Ask for bulk density and screen analysis on the certificate of analysis alongside chemical purity, and agree the sieve sizes in advance. Nuroil provides a CoA with every dense soda ash delivery and can arrange third-party inspection at loading on request; include your physical limits when you request a quote.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote