Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read7 sections

Knowledge centre · Waterproofing & construction

Cold asphalt properties and test methods explained

Workability, coating, stripping resistance, cohesion, strength and binder content: the properties that decide cold asphalt quality and how they are tested.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of a cold-applied roadway repair
On this page · 7 sections
  1. 01The balance a cold mix must strike
  2. 02Key properties and how they are checked
  3. 03Workability
  4. 04Stripping and moisture resistance
  5. 05Strength and stability
  6. 06Aggregate grading
  7. 07What to request from a supplier

Unlike paving bitumen, cold patching material has no single, universally adopted specification. Highway agencies write their own, and research reports note the lack of a standard mix design or performance specification. Buyers therefore need to know which properties matter and which tests are used to measure them. This guide sets out the main ones.

The balance a cold mix must strike

A cold asphalt must be soft enough to shovel and compact after months in a bag or stockpile, yet firm enough to carry traffic soon after placing. It must also keep its binder on the stone in wet conditions. Every property below relates to one side of that balance.

Key properties and how they are checked

PropertyWhat it meansHow it is assessed
WorkabilityHow easily the mix can be shovelled, spread and compacted, especially when coldLaboratory workability test such as ASTM D6704; slump-type tests; simple field shovel trials at low temperature
CoatingShare of aggregate surface covered with binderVisual coating assessment after mixing and after storage
Stripping resistanceAbility of the binder to stay on the stone when wetWater immersion or boiling-water tests, then visual estimate of retained coating
Cohesion and early strengthHow well the patch holds together soon after compactionCohesion or ravelling tests on freshly compacted samples
Cured strength and stabilityResistance to deformation once curedIndirect tensile strength or stability tests after a curing period
Binder content and residueHow much binder is present and how much remains after water or solvent leavesExtraction or distillation of the binder
Aggregate gradingParticle size distribution of the stoneSieve analysis
Storage stabilityWhether the mix stays workable and coated in packs or stockpilesRepeat workability and coating checks after a storage period

Workability

ASTM D6704 describes a laboratory method for measuring the workability of cold patching material that will be stockpiled or packaged, whether made with emulsion or cutback binder. The standard itself notes that its precision has not been established and that it should not be used for purchasing decisions, so treat it as a comparison tool. A research team in Texas developed a simple slump test for cold patch that showed good agreement between laboratory and field values. Many users also do a practical check: leave a bag in a cold room overnight and see whether it can still be shovelled easily.

Stripping and moisture resistance

Stripping is one of the most common problems with cold mix, both in storage and after placing. Good products use clean, compatible aggregate and often an antistrip additive. In a boiling or soaking test, a sample that keeps most of its stone surfaces coated with binder indicates good resistance; a sample that shows bare stone and cloudy water does not.

Strength and stability

Research on cold patch mixes uses indirect tensile strength and similar tests to measure how strength develops with curing time. A useful product shows reasonable early cohesion so it does not ravel under the first traffic, and good cured strength so it does not rut or shove later. Hot-climate users should pay particular attention to stability at high temperature.

Aggregate grading

Most cold patch products use a fairly open, well-graded aggregate, often with a maximum size around 6 to 10 mm for fine patching and somewhat larger for deeper repairs. Gradation affects how the mix compacts, how quickly solvent or water escapes and how smooth the finish is.

No single test proves a cold mix is good. Workability, stripping resistance and strength together describe whether it will place easily and stay in the hole.

What to request from a supplier

Ask for a technical data sheet giving binder type, aggregate grading, binder content, and any workability, stripping and strength results with test methods named. Ask for shelf life, storage conditions and the SDS. Nuroil supplies ready-to-use cold asphalt with a CoA for each delivery; send your specification through request a quote.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote