Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Guide3 min read6 sections

Knowledge centre · Caustic soda & soda ash

Troubleshooting caustic soda pearls: lumps, fines and low assay

Common problems with caustic soda pearls, from caking and dust to discolouration and low NaOH results, with likely causes and fixes.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of caustic soda pearls in a glass dish
On this page · 6 sections
  1. 01Symptom, cause and remedy
  2. 02Moisture: the root of most problems
  3. 03Getting a true analysis
  4. 04Handling bulk bags
  5. 05Preventing repeat problems
  6. 06Working with your supplier

Caustic soda pearls are chosen because they flow, feed and dissolve predictably. When they do not, production suffers: feeders block, solutions come out weak, or a batch of cleaner turns off-colour. Most problems trace back to a handful of causes, chiefly moisture and air. This guide lists the symptoms buyers report most often, what usually causes them and what to do.

Symptom, cause and remedy

SymptomLikely causeWhat to do
Lumps or a solid block in the bagMoisture entered through a damaged liner, unsealed bag or condensation in transitCheck liners and seals; store dry and off the floor; reduce stack height
Hopper bridging or rat-holingSticky pearls from humid air or vapour rising from the dissolving tankSeal and purge the hopper with dry air; add a vapour barrier at the outlet
Dust when tippingFines from abrasion in conveying or rough handlingHandle gently; specify a fines limit; fit dust extraction
Low NaOH on retestMoisture gain or carbonate formation; sample exposed during weighingTest NaOH and carbonate separately; tighten sampling technique
High carbonateLong exposure to air; air-sparged solution tanksKeep packs closed; mix with propeller or pump, not air
Yellow or grey tintIron or other metal contaminationCheck iron on the certificate; inspect handling equipment for corrosion
Cloudy solution or sedimentInsoluble impurities, carbonate reacting with hard water, or iron hydroxideUse softened water; filter; check iron and carbonate
Slow dissolvingPearls caked into larger lumps; weak agitation; cold make-up waterBreak lumps safely; improve mixing; use lukewarm water

Moisture: the root of most problems

Sodium hydroxide is strongly hygroscopic. A pearl exposed to humid air develops a film of concentrated caustic solution on its surface; neighbouring pearls stick together through these films and, as they dry or cool, set into lumps. The same moisture speeds up the reaction with carbon dioxide that converts hydroxide to carbonate. That is why caked product often also shows a lower NaOH and higher carbonate. The wet film is fully corrosive and attacks aluminium, zinc and galvanised steel, giving off hydrogen. Keep damp product away from such metals.

Getting a true analysis

Disputes over low assay often turn out to be sampling issues. Sample from inside the bag, transfer at once into a dry airtight bottle, take the carbonate portion first and weigh quickly. Report true NaOH, after precipitating carbonate with barium chloride, and carbonate separately, rather than a single total alkalinity figure. Standard methods such as ASTM E291 give a common basis for comparing laboratories.

Handling bulk bags

  • Keep the inner liner closed until the bag is in position over the hopper.
  • Discharge through a sealed spout connection to limit air contact and dust.
  • Do not leave part-used bulk bags open overnight; retie the liner and cover the bag.
  • Store bulk bags single-stacked unless the bag specification allows otherwise.

Preventing repeat problems

  • Agree a packing specification that includes a sealed polyethylene liner.
  • Specify a particle size range and a fines limit on the certificate of analysis.
  • Rotate stock first in, first out and avoid long storage in hot, humid areas.
  • Inspect containers on arrival for water ingress and torn bags.
Most pearl problems are moisture problems. Seal the packing, keep the air dry and test NaOH and carbonate separately when something seems wrong.

Working with your supplier

If a problem appears, record the lot numbers, take photographs, keep sealed retention samples and share your test results and methods. This makes it possible to tell a production issue from a transport or storage one. Nuroil supplies caustic soda pearls with a certificate of analysis for every lot and can arrange third-party inspection at loading; mention any past issues when you request a quote so packing can be specified accordingly.

PRODUCTS IN THIS GUIDE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote