Technical document

· PDF

Tell us who you are and the document downloads straight away. We use these details only to follow up on your requirement.

Samples & documents

What can we send you?

Tick what you need
Request a quote
Expert article3 min read5 sections

Knowledge centre · Caustic soda & soda ash

How much caustic soda flake to use for a solution of a set strength

Worked calculations for making 10%, 20% or 30% caustic solution from flakes, allowing for purity, density and the heat released.

Written by the Nuroil trade desk, Sharjah

Pencil sketch of caustic soda flakes in a glass dish
On this page · 5 sections
  1. 01The basic mass balance
  2. 02Working by volume
  3. 03Allow for the heat released
  4. 04Checking the result
  5. 05Safety and supply notes

Most plants that buy caustic soda flakes do not use them dry. They dissolve them to a working strength, often somewhere between 5% and 30% NaOH, and dose that solution. Getting the strength right matters for process control and for cost, yet make-up is often done by rule of thumb. This article sets out the simple arithmetic and the practical points that affect it.

The basic mass balance

Solution strength is normally expressed as percent by weight. To make a given mass of solution:

  • NaOH needed (kg) = mass of solution (kg) × target strength (%) ÷ 100
  • Flakes needed (kg) = NaOH needed ÷ flake purity (as a fraction)
  • Water needed (kg) = mass of solution − flakes

For example, 1,000 kg of 20% solution needs 200 kg of NaOH. With flakes assaying 98.5%, that is 200 ÷ 0.985 = 203 kg of flakes and about 797 kg of water. Using the certificate of analysis figure rather than assuming 100% avoids a systematic shortfall.

Working by volume

Tanks are measured in litres, not kilograms, and caustic solutions are denser than water. To fill a known volume you need the solution density at the target strength. The table uses commonly published densities at about 20 °C and flakes of 99% purity.

Target strength (% NaOH)Approx. density (kg/L)Mass of 1,000 L (kg)Flakes at 99% (kg)Water (kg)
10%1.111,110112998
20%1.221,220246974
30%1.331,330403927

Note that 1,000 L of finished solution needs slightly less than 1,000 L of water at 20% and above, because the dissolved caustic adds mass faster than it adds volume. Densities change with temperature, so check final strength when the batch has cooled.

Allow for the heat released

Dissolving caustic soda releases a great deal of heat: about 250 calories per gram of NaOH, or roughly 1,000 kJ per kilogram, across the usual working range. Making a 20% batch can raise the temperature by several tens of degrees, and stronger batches can approach boiling. This affects the procedure:

  • Start with water at moderate temperature. One major producer recommends lukewarm water of about 27 to 38 °C, neither hot nor cold.
  • Always add flakes to water, slowly, onto the surface of a well-stirred tank. Never add water to flakes.
  • Use a propeller agitator or a recirculation pump. Without agitation flakes sink and form a slowly dissolving hydrate layer that can overheat locally and spatter violently.
  • Do not stir with compressed air, which adds carbon dioxide and raises the carbonate content.
  • Make sure the tank material and any plastic liner are rated for the peak temperature, and allow the batch to cool before checking strength.

Checking the result

A hydrometer reading converted with a density table gives a quick strength check once the solution is at a known temperature. For tighter control, titrate a weighed sample with standard hydrochloric acid. Record the lot number of the flakes used, so any strength problem can be traced back to the raw material.

Use the certificate of analysis purity in your calculation, add flakes to water slowly with good mixing, and check strength only after the batch has cooled.

Safety and supply notes

Wear the protective equipment given in the safety data sheet, including chemical goggles with a face shield, alkali-resistant gloves and apron. Keep an eyewash and safety shower close to the make-up area. When ordering flakes, ask for the guaranteed minimum NaOH content and a lot-specific certificate of analysis so your make-up calculation rests on real numbers. If you dissolve large tonnages every day, compare the cost of handling flakes with taking ready-made lye from the wider caustic soda range. Nuroil can advise on both; see caustic soda flakes or request a quote.

PRODUCTS IN THIS ARTICLE
KEEP READING

More from the Knowledge Centre.

STILL HAVE A QUESTION?

Ask the people who trade it every day.

Our trade managers answer technical and commercial questions about grades, specifications, packing and shipping.

LET’S TALK ABOUT YOUR REQUIREMENTS

Your next shipment starts here.

Request a quote